Ingersoll Rand 1103 Manual De Instrucciones
Ingersoll Rand 1103 Manual De Instrucciones

Ingersoll Rand 1103 Manual De Instrucciones

Llaves de carraca super pesadas

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 13

Enlaces rápidos

OPERATION AND MAINTENANCE MANUAL
Models 1103 and 1133 Ratchet Wrenches are designed for muffler and shock absorber
work, replacement of water pumps, radiators and air conditioning units and general
automotive repair.
IMPORTANT SAFETY INFORMATION ENCLOSED - - SAVE THESE INSTRUCTIONS
READ AND UNDERSTAND THIS MANUAL BEFORE OPERATING THIS PRODUCT
IT IS YOUR RESPONSIBILITY TO MAKE THIS SAFETY INFORMATION
AVAILABLE TO OTHERS THAT WILL OPERATE THIS PRODUCT
FAILURE TO OBSERVE THE FOLLOWING WARNINGS COULD
Always install, operate, inspect and maintain this
product in accordance with all applicable standards
and regulations (local, state, country, federal, etc.).
Always use clean, dry air at 90 psig (6.2 bar/620 kPa)
maximum air pressure at the inlet. Higher pressure
may result in hazardous situations including excessive
speed, rupture, or incorrect output torque or force.
Be sure all hoses and fittings are the correct size and
are tightly secured. See Dwg. TPD905- - 1 for a typical
piping arrangement.
Ensure an accessible emergency shut off valve has
been installed in the air supply line, and make others
aware of its location.
Always wear eye protection when operating or
performing maintenance on this tool.
Always wear hearing protection when operating this
tool.
Always use Personal Protective Equipment
appropriate to the tool used and material worked.
This may include dust mask or other breathing
apparatus, safety glasses, ear plugs, gloves, apron,
safety shoes, hard hat and other equipment.
This tool is not designed for working in explosive
environments, including those caused by fumes and
dust, or near flammable materials.
This tool is not insulated against electric shock.
Prevent exposure and breathing of harmful dust and
particles created by power tool use.
Some dust created by power sanding, sawing,
grinding, drilling, and other construction
activities contains chemicals known to cause
cancer, birth defects or other reproductive harm.
Some examples of these chemicals are:
- - lead from lead based paints,
- - crystalline silica from bricks and cement and
other masonry products, and
- - arsenic and chromium from chemically
treated lumber.
Your risk from these exposures varies, depending
on how often you do this type of work. To reduce
your exposure to these chemicals: work in a well
ventilated area, and work with approved safety
equipment, such as those dust masks that are
specially designed to filter out microscopic
particles.
Refer all communications to the nearest Ingersoll- -Rand
Office or Distributor
 Ingersoll- - Rand Company 2002
Printed in Japan
FOR 1103 AND 1133 ULTRA DUTY
RATCHET WRENCHES
CAUTION
NOTICE
RESULT IN INJURY
PLACING TOOL IN SERVICE
USING THE TOOL
04578431
Do not use damaged, frayed or deteriorated air hoses
and fittings.
Keep clear of whipping air hoses. Shut off the
compressed air before approaching a whipping hose.
Always turn off the air supply and disconnect the air
supply hose before installing, removing or adjusting
any accessory on this tool, or before performing any
maintenance on this tool.
Do not lubricate tools with flammable or volatile
liquids such as kerosene, diesel or jet fuel. Use only
recommended lubricants.
Keep work area clean, uncluttered, ventilated and
illuminated.
Do not remove any labels. Replace any damaged label.
Be aware of buried, hidden or other hazards in your
work environment. Do not contact or damage cords,
conduits, pipes or hoses that may contain electrical
wires, explosive gases or harmful liquids.
Keep others a safe distance from your work area, or
ensure they use appropriate Personal Protective
Equipment.
Keep hands, loose clothing, long hair and jewelry
away from working end of tool.
Power tools can vibrate in use. Vibration, repetitive
motions or uncomfortable positions may be harmful
to your hands and arms. Stop using any tool if
discomfort, tingling feeling or pain occurs. Seek
medical advice before resuming use.
Keep body stance balanced and firm. Do not
overreach when operating this tool. Anticipate and be
alert for sudden changes in motion, reaction torques,
or forces during start up and operation.
Tool and/or accessories may briefly continue their
motion after throttle is released.
To avoid accidental starting - - ensure tool is in "off"
position before applying air pressure, avoid throttle
when carrying, and release throttle with loss of air.
Ensure work pieces are secure. Use clamps or vises to
hold work piece whenever possible.
Do not carry or drag the tool by the hose.
Do not use power tools when tired, or under the
influence of medication, drugs, or alcohol.
Never use a damaged or malfunctioning tool or
accessory.
Do not modify the tool, safety devices, or accessories.
Do not use this tool for purposes other than those
recommended.
Use accessories recommended by Ingersoll- - Rand.
Form P7562- -EU1
Edition 1
GB
March, 2002

Publicidad

Tabla de contenido
loading

Resumen de contenidos para Ingersoll Rand 1103

  • Página 1 RATCHET WRENCHES CAUTION NOTICE Models 1103 and 1133 Ratchet Wrenches are designed for muffler and shock absorber work, replacement of water pumps, radiators and air conditioning units and general automotive repair. IMPORTANT SAFETY INFORMATION ENCLOSED - - SAVE THESE INSTRUCTIONS...
  • Página 2: Warning Symbol Identification

    Model Drive Drive Thread Inches ft- - lbs (Nm) Pressure Power Type (mm) 1103 1/4” 5- - 23 (7- - 31) 1/4” NPT 1/4 (6.35) 1133 3/8” 5- - 25 (7- - 34) 1/4” NPT 1/4 (6.35) Tested in accordance with PNEUROP PN8NTC1.2...
  • Página 3: Declaration Of Conformity

    (supplier’s name) Swan Lane, Hindley Green, Wigan WN2 4EZ (address) declare under our sole responsibility that the product, 1103 AND 1133 Ratchet Wrenches to which this declaration relates, is in compliance with the provisions of 98/37/EC Directives. ISO8662, PNEUROP PN8NTC1- 2 By using the following Principle Standards: (2002 →...
  • Página 4: Mise En Service De L'outil

    MODE D’EMPLOI DES CLES A ROCHET HAUTES PERFORMANCES MODELES 1103 ET 1133 NOTE Les clés à rochet Modèles 1103 et 1133 sont destinées aux opérations sur silencieux et amortisseurs, au remplacement des pompes à eau, des radiateurs et des climatiseurs et aux réparations automobiles générales.
  • Página 5: Signification Des Symboles D'avertissement

    Type de pouces tr/mn Ft- - lb (Nm) Pression Puissance filetage (mm) 1103 1/4” 5- - 23 (7- - 31) 1/4” NPT 1/4 (6,35) 1133 3/8” 5- - 25 (7- - 34) 1/4” NPT 1/4 (6,35) Test selon PNEUROP PN8NTC1.2...
  • Página 6: Certificat De Conformité

    (nom du fournisseur Swan Lane, Hindley Green, Wigan WN2 4EZ (adresse déclarons sous notre seule responsabilité que le produit: Cles A Rochet Serie Forte Modele 1103 et 1133 objet de ce certificat, est conforme aux prescriptions des Directives: 98/37/EC ISO8662, PNEUROP PN8NTC1.2 en observant les normes de principe suivantes: (2002 →...
  • Página 7 März, 2002 BEDIENUNGSANLEITUNG FÜR HOCHLEISTUNGS- - RATSCHENSCHRAUBER DER BAUREIHEN 1103 UND 1133 HINWEIS Ratschenschrauber der Baureihen 1103 und 1133 werden eingesetzt für Arbeiten am Schalldämpfer und Stoßdämpfer, zum Auswechseln von Wasserpumpen, Kühlern und Klimaanlagen sowie für allgemeine Fahrzeugreparaturen. ACHTUNG NACHFOLGEND WICHTIGE SICHERHEITSHINWEISE - - DIESE ANWEISUNGEN SIND SORGFÄLTIG AUFZUBEWAHREN...
  • Página 8: Identifikation Von Warnsymbolen

    U/min Ft- - lb (Nm) Druck Leistung Gewindeart Zoll (mm) 1103 1/4” 5- - 23 (7- - 31) 1/4” NPT 1/4 (6,35) 1133 3/8” 5- - 25 (7- - 34) 1/4” NPT 1/4 (6,35) Gemäß PNEUROP PN8NTC1.2 geprüft...
  • Página 9: Konformitätserklärung

    (Name des Herstellers) Swan Lane, Hindley Green, Wigan WN2 4EZ (Adresse) erklären hiermit, gemäß unserer alleinigen Verantwortung, daß die Geräte: Hochleistungs- Ratschenschrauber Baureihe 1103 und 1133 auf die sich diese Erklärung bezieht, den Richtlinien: 98/37/EG unter Anlehnung an die folgenden Grundnormen ISO8662, PNEUROP PN8NTC1.2...
  • Página 10: Messa In Servizio Dell'attrezzo

    SUPER DUTY MODELLI 1103 E 1133 AVVISO Le chiavi a crichetto modello 1103 e 1133 sono state progettate per lavori su marmitte e su ammortizzatori, per la sostituzione di pompe dell’acqua, di radiatori e di unità di climatizzazione e riparazioni generali di automezzi.
  • Página 11: Identificazione Dei Simboli Di Avvertenza

    Modello dell’aria Tipo di fi- poll. giri/min Ft- - lb (Nm) Pressione Potenza lettatura (pollici) 1103 1/4” 5- - 23 (7- - 31) 1/4” NPT 1/4 (6,35) 1133 3/8” 5- - 25 (7- - 34) 1/4” NPT 1/4 (6,35) Test in conformità con PNEUROP PN8NTC1.2...
  • Página 12: Dichiarazione Di Conformità

    Swan Lane, Hindley Green, Wigan WN2 4EZ (indirizzo) dichiariamo sotto la nostra unica responsabilità che il prodotto: Chiavi a cricchetto Heavy Duty modello 1103 e 1133 a cui si riferisce la presente dichiarazione è conforme alle normative delle direttive: 98/37/CE ISO8662, PNEUROP PN8NTC1.2...
  • Página 13: Para Poner La Herramienta En Servicio

    SUPER PESADAS MODELOS 1103 Y 1133 NOTA Las llaves de carraca modelos 1103 y 1133 están diseñadas para trabajos en silenciadores y amortiguadores, sustitución de bombas de agua, radiadores y equipos de aire acondicionado, así como para la reparación de automóviles en general.
  • Página 14: Identificación De Símbolos De Aviso

    Modelo de aire Thread Inches pulg. Ft- - lb (Nm) Presión Potencia Type (mm) 1103 1/4” 5- - 23 (7- - 31) 1/4” NPT 1/4 (6,35) 1133 3/8” 5- - 25 (7- - 34) 1/4” NPT 1/4 (6,35) Comprobado conforme a le norma PNEUROP PN8NTC1.2...
  • Página 15: Declaración De Conformidad

    Swan Lane, Hindley Green, Wigan WN2 4EZ (domicilio) Declaramos que, bajo nuestra responsabilidad exclusiva, el producto: Llaves de Carraca Industriales Modelo 1103 y 1133 a los que se refiere la presente declaración, cumplen con todo lo establecido en las directivas: 98/37/CE ISO8662, PNEUROP PN8NTC1.2...
  • Página 16: Ingebruikneming Van Het Gereedschap

    INSTRUCTIES VOOR TYPEN 1103 EN 1133 RATELSLEUTELS VOOR ZEER ZWAAR WERK LET WEL De Ratelsleutels van het Type 1103 en 1133 zijn bestemd voor werkzaamheden aan dempers en schokbrekers, vervanging van waterpompen, radiatoren en airco- -installaties, en algemene autotechnische werkzaamheden.
  • Página 17: Identificatie Waarschuwingssymbool

    Type Type Schroef- inch inch Ft- - lb (Nm) Deuk Vermogen draadtype #(mm) 1103 1/4” 5- - 23 (7- - 31) 1/4” NPT 1/4 (6,35) 1133 3/8” 5- - 25 (7- - 34) 1/4” NPT 1/4 (6,35) Getest overeenkomstig PNEUROP PN8NTC1.2...
  • Página 18 (naam leverancier) Swan Lane, Hindley Green, Wigan WN2 4EZ (adres) verklaren, onder onze uitsluitende aansprakelijkheid, dat het produkt: Type 1103 en 1133 Ratelsleutels voor Zwaar Werk waarop deze verklaring betrekking heeft overeenkomt met de bepalingen van directieven: 98/37/EG ISO8662, PNEUROP PN8NTC1.2...
  • Página 19: Maintenance Instructions

    For 1103 (1/4” square drive) 1103- - TRK1 25 Front End Plate 1103- - 11 For 1133 (3/8” square drive) 1133- - TRK1 26 Ball Bearing 1103- - 97 *50 Spline Wrench (to remove 1103- - 406) 1103- - SW * Part not included.
  • Página 20 Service Centers Centres d’entretien Ingersoll- - Rand Niederlassungen Centri di Assistenza Centros de Servicio Service Centra Ingersoll--Rand Company Ingersoll--Rand Nederland 510 Hester Drive Produktieweg 10 White House 2382 PB Zoeterwoude TN 37188 Nederland Tel: (31) 71 452200 Tel: (615) 672--0321 Fax: (31) 71 218671 Fax: (615) 672--0801 Ingersoll--Rand Company SA...

Este manual también es adecuado para:

1133

Tabla de contenido