Vimar Elvox 6601/AU Instrucciones Instalador página 6

Portero aut. manos libres due fili (de empotrar / de sobremesa / de superficie)
Ocultar thumbs Ver también para Elvox 6601/AU:
Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 18
6600
DESCRIPTION
Types 6601/AU, 660C/AU, 6701/AU are open voice interphone series 6600
to be used in DUE FILI ELVOX (two wire Elvox) audio/video entrance panel
systems.
Type .../F versions have the same features and are programmed and in-
stalled in the same way.
They are equipped as standard with 8 push-buttons for the following func-
tions: door lock release, self-start of interphone in the system even when
it has not been called, conversation, stair light, internal voice line volume
control, ringtone volume control, brightness control and ringtone type set-
ting. Two LEDs (red and green) on the interphone serve to indicate the
following states: call signal mute, unanswered calls, services not available
and gate/door open.
- Flush-mounting of the interphone requires the use of flush-mounted back
box type 6149 or the brackets type. R660 (for plasterboard).
- The surface wall-mounted installation for the interphone (6701) requires
the brackets for the wall-mounting supplied as standard.
Fig. 1
C
D
F
G
D
L
Interphone technical specifications
- Interphone in ABS.
- Removable terminal block.
- Electronic circuit on interchangeable cards.
- Operating temperature from 0° to +40° C.
- Electronic ringtone.
- Input for landing calls with different ringtone from entrance panel calls.
- Output for additional ringtone type 860A.
- Supply voltage provided by bus.
Controls and adjustments
B) Microphone.
C) Loudspeaker.
D)
Pair of push-buttons.
1) When the interphone is ON, the push-buttons can be used to adjust
the brightness.
2) When the interphone is OFF, the push-buttons can be used to select
the tune for calls from a speech unit only. To program the tune: hold
down 1 of the 2 push-buttons for at least 1 second, then press the
push-buttons repeatedly to select the desired tune.
E)
Pair of push-buttons.
1) During conversation, with push-button "I" pressed, press push-but-
tons "E" to increase or decrease the volume of the internal voice line.
2) To adjust ringtone volume: hold down 1 of the 2 push-buttons "E" for
at least 1 second, then press the push-buttons repeatedly to increase
or reduce ringtone volume, or mute the ringtone.
F) Push-button
for activating 1st auxiliary service if connected (e.g.
stair lights).
G) Push-button
: to open the lock and terminate any conversation
in progress.
H) Push-button
: for self-start of the interphone without the latter being
called.
6
B
E
H
I
M
E
I)
Two-channel conversation push-button: after the call and/or
switch-on of the monitor press the pushbutton once to activate the
audio. Pressing it once again the conversation terminates.
The red LED remains lit for the whole conversation dwell..
L)
Door open signal: if the green LED lights up, this indicates that
the door is open (the function is optional according to the type of instal-
lation).
M)
'Ringtone mute' LED: if the red LED lights up, this indicates that
the call is disabled (see point "E").
The red LED also remains lit for the entire duration of the conversation,
i.e. while the audio is active.
N.B. On the back of the interphones type 6601/AU and 6701/AU is a RESET
push-button for use during programming, while on interphone type 660C/
AU the RESET push-button is on the bottom of the table-top conversion kit;
all are equipped with the A-B-C connectors for stabilising the video signal.
Connection and connector terminal board
+12, CH) Additional ringtone connection.
1, 2)
BUS line.
E+, E- )
Additional supply voltage for interphone with power supply
type 6923.
FP, M)
Connection for landing call push-button.
INSTALLATION 6601/AU
- Install the interphone away from sources of light and heat.
- Flush-mount back box type 6149 in the wall at a height of approximately
1.4 m above the ground.
- Remove the plastic cross-piece from the back box (see part. 1, Fig. 2)
- Carry out the terminal block connections (see wiring diagram).
- Fix the video interphone to the back box with the 4 screws supplied (fig.
2).
- Fit the side panels, taking care that the panel with the slot for the micro-
phone is fitted on the right (fig. 2).
Flush-mounted
version
Fig. 2
139
136
mm
59mm
141 mm
10mm
(
)
Microphone
Part. 1

Publicidad

Tabla de contenido
loading

Tabla de contenido