Sevylor RAPTOR TFT260 Manual De Utilización página 5

If you leave your product exposed to the hot sun check the pressure and deflate it slightly, to avoid
overstretching the material.
The ambient temperature affects the tube's internal pressure : a variation of 1° C (1.8° F) causes a variation of the
pressure in the tube of +/- 4 mBar (0.06 PSI).
OPERATING INSTRUCTIONS
Use the boat only in protected shore-zones, avoid open water and streams with strong currents.
BEWARE OF OFFSHORE WINDS AND CURRENTS !
Observe local regulations and hazards related to water activities and boat operation.
Before using the product, please check it carefully.
A bad distribution of the load can destabilise the boat and may result in a loss of control.
Always wear a life vest approved by proper authorities.
Do not exceed the maximum number of persons or weight.
Avoid all contact between the buoyancy tubes and sharp objects or harsh liquids (such as acid).
This product is equipped with ropes. Keep the ropes away from children.
Keep the carry bag away from children. DANGER OF SUFFOCATION!
If, after an accident, a compartment deflates, bring it inside the boat and return to shore at reduced speed. The boat is
kept above water by the security system and by the strong buoyancy.
MAINTENANCE : DEFLATING – FOLDING THE ITEM – CLEANING – WINTER STORAGE
1. Remove oars/paddles and other accessories.
2. To deflate, unscrew the valve insert(s).
3. Clean and check the item and all the accessories after each use. Rinse it thoroughly making sure that any salt
residues are removed, if it has been used in salt water. Use a mild soapy solution, but do not use detergents or any
type of silicone-based products. Make sure that the product is completely dry before putting it away.
4. Fold the sides into the middle, then roll it up from the opposite end of the valves (so remaining air can escape from
the valves); start again if you feel there is still some air in the tubes.
5. When storing your inflatable, keep it in a clean and dry place, away from extreme temperature variations or other
potentially damaging factors. It can be stored deflated and rolled up in its bag or assembled and lightly inflated. Store
it away from rodents.
Water will enter between the outer hull and inside chambers, this is O.K ; however, whenever you take this
item out of the water and deflate it, allow it to air out and dry, neither the skin/hull or the inside chambers will
suffer from water damage, but stagnant water could cause mildew and foul odour.
HOW TO REPAIR SMALL PUNCTURES
You can repair small punctures with the included repair kit (NOTE: Glue not included in USA.). Please note that in order
for the repair to be successful, the humidity level should be less than 60%, temperature between 65° F/77° F or
18° C/25° C. Avoid carrying out repairs in the rain or in direct sunlight.
To remove the inside bladder(s) please open the zipper on the inside of the Nylon hull. Check that the tube is fully
deflated and lies flat.
1. Draw the shape of the patch exactly where it will be applied, cut a round patch at least 2" / 5 cm larger than the
cut/damaged area.
2. Clean the damaged area and the corresponding side of the patch with a grease remover of the alcohol type and
allow for it to dry for 5 minutes.
3. Apply 3 thin layers of glue on both the patch and the damaged area, allow for it to dry for 5 minutes between layers
until the glue feels tacky.
4. When the third layer of glue is dry, apply the patch without pressing and adjust the positioning if required, press the
air bubbles which may have formed under the patch by smoothing the patch with a round object such as a spoon, do
this procedure by starting in the center of the patch towards the outside, clean the excess glue with a solvent.
Drying : 12 hours.
Perform repairs in a well-ventilated area.
Avoid inhaling glue vapours or swallowing the glue.
N.B. The seams must not be glued. Only the manufacturer of the boat can perform repairs on the seams.
WARNING !
WARNING !
WARNING !
WARNING !
Avoid contact with the skin or the eyes.
Keep all repair materials (glue, solvents, etc.)
out of the reach of children.
5
E
N
G
L
I
S
H
outo