Service Menu - Lamborghini Caloreclima FL 24 TCS Instrucciones De Uso, Instalación Y Mantenimiento

A - Upstream pressure point
B - Downstream pressure point
R
I - Gas valve electrical connection
R - Gas outlet
S - Gas inlet
B
I
A TYPE SGV100
Pi max 65 mbar
24 Vdc - class B+A
S
fig. 18 - Gas valve
Heating power adjustment
To adjust the heating power, switch the boiler to TEST mode (see sec. 4.1). Press the
heating buttons detail 3 - fig. 1 to increase or decrease the power (min. = 00 - max. =
100). Press the reset button within 5 seconds and the max. power will remain that just
set. Exit TEST mode (see sec. 4.1).
Configuration Menu
Press the DHW buttons together for 10 seconds to access the configuration Menu. 8 pa-
rameters are available, indicated by the letter "b", which are not modifiable from Remote
Timer Control.
Press the Heating buttons to scroll the list of parameters in increasing or decreasing or-
der. Press the DHW buttons to view or modify the value of a parameter: the modification
will be automatically saved.
Contents Description Range
0=Natural Gas
b01 Gas type selection
1=LPG
1=Bithermal
instantaneous
2=Monothermal
instantaneous
b02 Boiler type selection
3=Heating only
(3-way valve)
4=Heating only
(circulating pump)
0=Sealed Chamber
combustion control
(without fume
pressure switch)
1=Open Chamber
(with fume thermostat)
2=Sealed Chamber
(with fume pressure
switch)
3=Sealed Chamber
Combustion chamber type
b03
combustion control
selection
(with fume thermostat
on recuperator)
4=LOW NOx Sealed
Chamber Combustion
control
(without fume
pressure switch)
5=LOW NOx Open
Chamber
(with fume thermostat)
18
EN
1 2 3 4
~ 24W
fig. 19 - Gas valve connection
Default
0=Natural Gas 0=Natural Gas
1=Bithermal instanta- 3=Heating only (3-way
neous valve)
0=Sealed Chamber
0=Sealed Chamber with
with combustion control
combustion control (without fume
pressure switch)
cod. 3541D700 - Rev. 01 - 03/2018
Contents Description
Primary Exchanger type
selection
(b03=0)
No effect on adjustment
(b03=1)
No effect on adjustment
(b03=2)
b04
Primary Exchanger type
selection
~ 65W
(b03=3)
No effect on adjustment
(b03=4)
No effect on adjustment
(b03=5)
Relay card LC32
operation selection (b02=1)
No effect on adjustment
b05
(b02=2)
No effect on adjustment
(b02=3)
No effect on adjustment
(b02=4)
b06 Mains Voltage Frequency
Comfort burner on time
(b02=1)
No effect on adjustment
(b02=2)
b07
No effect on adjustment
(b02=3)
No effect on adjustment
(b02=4)
b08 Gas valve driver
Notes:
1. Parameters with more than one description vary their function and/or range in rela-
tion to the setting of the parameter given in brackets.
2. Parameters with more than one description are reset to the default value if the pa-
FL 24 TCS
rameter given in brackets is modified.
To exit the configuration Menu press the DHW buttons together for 10 seconds, or exiting
occurs automatically after 2 minutes.

Service menu

The card Service Menu is accessed by pressing the Reset button for 20 seconds. 4 sub-
menus are available: press the Heating buttons to select, in increasing or decreasing or-
der, "tS", "In", "Hi" or "rE". "tS" means Transparent Parameters Menu, "In" means
Information Menu, "Hi" means History Menu: after selecting the submenu, press the Re-
set button again to access it; "rE" means History Menu Reset: see description.
"tS" - Transparent Parameters Menu
16 parameters indicated by the letter "P" are available: which are also modifiable from
Remote Timer Control.
Press the Heating buttons to scroll the list of parameters in increasing or decreasing or-
der. Press the DHW buttons to view or modify the value of a parameter: the modification
will be automatically saved.
Contents Description
P01 Ignition ramp Offset
P02 Heating ramp
P03 Heating standby time
P04 Heating Post-Circulation
P05 Heating user max. set point
P06 Max. output in heating
Burner shutdown in hot water
production (b02=1)
P07
Burner shutdown in hot water
production (b02=2)
Hot water tank hysteresis
(b02=3)
Hot water tank hysteresis
(b02=4)
FL 24 TCS - 32 TCS
Range Default
0=Flat
1=Omega 0=Flat
2=--
-- 0
-- 0
0=Flat
1=Omega 0=Flat
2=--
-- 0
-- 0
0=External gas valve
1=System filling sole-
0=External gas valve
noid valve
2=Solar 3-way valve
-- 0
-- 0
-- 0
0=50Hz
0=50Hz
1=60Hz
0-20 seconds 5 seconds
-- 5
-- 5
-- 5
0 = Standard, 1 0=Standard
Range Default
0-40 20
1-20°C/minute 5°C/minute
0-10 minutes 2 minutes
0-20 minutes 6 minutes
31-85°C 80°C
0-100% 100%
0=Fixed
1=Linked to set point
2=Solar (5) 0=Fixed
3=Solar (10)
4=Solar (20)
0=Fixed
1=Linked to set point
2=Solar (5) 0=Fixed
3=Solar (10)
4=Solar (20)
0-4°C 2°C
0-4°C 2°C
FL 24 TCS
0=Flat
0
0=50Hz
5
0=Standard
FL 24 TCS
20
5°C/minute
2 minutes
6 minutes
80°C
100%
2°C