Peg-Perego pliko switch Instrucciones De Uso página 18

EN_English
Thank you for choosing a Peg-Pérego product.
WARNING
_ IMPORTANT: read the instructions carefully before
use and keep them for future reference. The child
may be hurt if you do not follow these instructions.
_ This item was designed for the transport of 1 child
in the seat and 1 one child standing on the rear
footboard.
_ Do not use this item for a number of occupants
greater than that intended by the manufacturer.
_ The Pliko Switch Chassis + Pliko Switch car seat is
approved for infants from birth up to 15 kg in weight.
The rear ledge is approved for transporting a second
child of up to 20 kg in weight.
_ The Pliko Switch chassis is designed for use with Peg-
Pérego Ganciomatic products: the Pliko Switch chassis
+ Primo Viaggio car seat (0+ group) is approved for
children from birth up to 13 kg of weight. The Pliko
Switch chassis + "Navetta" or "Primonido" bassinet
unit is approved for children from birth up to 10 kg of
weight. If using with the "Navetta" or the "Primonido",
refrain from using the rear ledge.
_ Before use check that the Peg-Pérego Ganciomatic
products are correctly fixed to the item.
_ It may be dangerous to leave your child unattended.
_ Always use the 5-point harness and attach the waist
strap to the leg divider strap.
_ Be careful not to hurt the child when adjusting the
mechanisms (handlebar, backrest).
_ Always apply the brake when stopped and when
positioning the child in the seat or when removing
the child from the seat.
_ Assembly and preparation of the product, plus
cleaning and maintenance operations, must be
carried out exclusively by adults.
_ Do not use this item if there are parts missing or signs
of breakage.
_ Before use check that all the attachment mechanisms
are correctly engaged.
_ Do not insert fingers into the mechanisms.
_ Any load hanging on the handlebar or the handles
can make the stroller/carriage unstable; follow the
manufacturer's instructions for max load capacity.
_ Do not place loads over 5 kilos in the basket. Do not
place in the bottle holder weights heavier than stated
or hot drinks. Do not place in the hood pockets (if
applicable) weights over 0.2 Kg.
_ The front bar is not designed to support the child's
weight. It is not designed to keep the child in the seat
and does not substitute for the waist belt.
_ Do not use the item near to stairs or steps, heat
sources, naked flames or dangerous objects within
reach of the child.
_ The use of accessories not approved by the
manufacturer could be dangerous.
_ This item is not suitable for jogging or roller skating.
_ Do not use the rain canopy (if present) indoors and
regularly check to ensure the child is not too warm;
do not park the stroller close to heat sources and
keep well away from lighted cigarettes. Ensure the
rain canopy is not interfering with any moving parts
of the carriage or stroller; always remove the rain
canopy before folding your carriage or stroller.
_ When using the stroller with two children, never leave
them unattended and do not allow the second child
to climb onto the rear ledge with the stroller empty.
_ Do not use the release levers to move or lift the
stroller when the child is in it.
FEATURES OF THE ITEM
_ The item is numbered progressively.
_ Pliko Switch is a stroller with a reversible seat: facing
the person pushing or facing forwards.
_ Pliko Switch is made up of two elements: Pliko Switch
CHASSIS and Pliko Switch SEAT.
COMPONENTS OF THE ITEM
Check the contents of the packaging and if you have
any complaints please contact the Assistance Service.
_ Pliko Switch Chassis: basket; 2 swivelling or locking
front wheels; 2 rear wheels with brake cable and cup
holder.
_ Pliko Switch Seat: front bar; hood; cover; rain canopy.
INSTRUCTIONS
1 PACKING PROTECTION: before opening the chassis
remove the protection (fig_a), otherwise it will not
open correctly (fig_b).
2 OPENING: raise the two levers together (fig_a) and
pull upwards until the chassis is completely open
(fig_b). Check that the chassis is correctly opened: the
side tubes must be locked together (fig_c).
3 FITTING THE FRONT WHEELS: press the lever of the
two front wheels (fig_a), insert the wheel until it
clicks into place (fig_b) and check that it is securely
attached (fig_c).
4 FITTING THE REAR WHEELS: carefully distinguish
between the two rear wheels connected by the brake
cable: the rear left wheel features a slot that matches
a corresponding rib on the rear left chassis tube. Press
in the wheels until they click into place (fig_a) and
check that they are firmly attached (fig_b).
5 FITTING THE BASKET: insert the loops over the front
hooks (fig_a) and rear hooks (fig_b) and button down
the two flaps around the front tube (fig_c).
6 FITTING THE CUP HOLDER: insert the cup holder on
the corresponding peg and press down until it clicks
into place (fig_a). The cup holder can be attached to
either side of the chassis.
7 EXTENDABLE HANDLES: to extend the handles press
the top of the button and lift upwards the same time
(fig_a); to retract the handles press the bottom of the
button and push the handle downwards at the same
time (fig_b).
8 FIXED OR SWIVELLING FRONT WHEELS: lift the levers
to prevent the front wheels from swivelling (fig_a),
lower the levers to allow the front wheels to swivel
(fig_b). On uneven surfaces the wheels should be set
to their fixed position.
9 REAR WHEELS WITH CENTRAL BRAKE CABLE: press a
brake lever to immobilise the stroller (fig_a), lift the
lever to release it (fig_b).
- 18 -