Serial Numbers - Peg-Perego pliko switch Instrucciones De Uso

10 MOUNTING THE SEAT TO THE CHASSIS: the reversible
seat can be attached to the chassis either facing
the person pushing the stroller (fig_a), or facing
forwards (fig_b), place the seat on the chassis so
that it is aligned with the relative symbols and press
downwards with both hands until you hear two clicks
confirming that it has locked into position. Ensure
the seat is correctly secured by attempting to pull it
upwards by gripping the front bar.
11 REMOVING THE SEAT FROM THE CHASSIS: move the
two levers in the direction of the arrow (fig_a) and lift
the two handles up (fig_b) until release. Pull the two
handles upwards until the seat is released. The seat
can be removed from and re-attached to the chassis
also when it is occupied by a child.
12 FRONT BAR: to attach the front bar, slide the
connections into the end of the armrests, press the
two side buttons and push the bar towards the seat
until it clicks into place (fig_a). To remove the front
bar press the two buttons and pull it outwards (fig_b).
Open the front bar at one side only so that the child
can be positioned in or removed from the seat more
easily.
13 BACKREST: to recline the backrest lift the lever (fig_a)
and choose one of the 4 positions (fig_b).
14 FOOTREST: to lower the footrest push the two levers
downwards and then push the footrest downwards
(fig_a); to raise the footrest lift it upwards (fig_b).
15 5-POINT SAFETY HARNESS: to attach the safety
harness, insert the two buckles of the waist strap
(with shoulder straps attached – arrow_a) into the
leg divider strap until it clicks into place (arrow_b). To
release, push the round button placed in center of the
buckle upwards (arrow_c) and pull the waist strap to
the sides (arrow_d).
16 To tighten the waist strap, pull on both sides in the
direction of the arrow (arrow_a). To loosen it do the
opposite. The waist strap can be tightened as far as
the safety lock (fig_b).
17 To adjust the height of the safety harnesses, release
the two buckles on the rear of the backrest.
Pull the shoulder straps towards you (arrow_a) until
the buckles are released and insert them in the
backrest loops (arrow_b). Remove the shoulder straps
from the sack (arrow_c) and insert them in the most
appropriate loop (arrow_d), then re-attach the two
buckles on the rear of the backrest (arrow_e) The
buckles are securely attached when a click is heard
(fig_f).
18 HOOD: to attach the hood insert the connections
into the sides of the seat (fig_a) and then fasten the
buttons on the rear of the backrest (fig_b). To remove
the hood: disengage the connections and unbutton
from the backrest. To raise the hood: pull it towards
you; to close the hood: push it back. To convert the
hood into a sun canopy, open the double zipper
(fig_c) and unfasten the buttons on the rear of the
backrest.
19 COVER: fit the cover and button under the footrest
(fig_a). For the carriage version, lift the footrest
and position the cover above the front bar (fig_b),
securing it with the elastic loops to the hood buttons
(fig_c).
20 For the stroller version, lower the footrest, insert the
cover underneath the front bar (fig_a) and secure it
according to the model purchased A, B, C.
21 The seat of Pliko Switch model Soft is reversible.
Before proceeding, remove the straps and replace
them (see paragraph 17) once the operation has been
completed. To reverse it, unbutton the upper sack
from the lower sack in the footrest area (fig_a), open
the zipper along the backrest (fig_b) and re-position
the sack from the opposite side.
22 RAIN CANOPY: position the rain canopy on the stroller
(fig_a) and insert the two lateral loops over the hood
buttons (fig_b).
23 Secure the rain canopy by attaching the elastic loop
to the rear uprights (fig_a) or to the front uprights
(fig_b), according to the seat position.
24 REAR LEDGE: the rear ledge makes it easier to
negotiate kerbs or level differences with the stroller
(fig_a) and can also be used to transport a second
child (fig_b). To use the stroller with two children,
apply the brakes, position the smaller child in the seat
and attach the safety harness (1). Grip the handles (2)
and help the second child to climb onto the ledge (3).
25 FOLDING: the stroller can be folded without the
seat, with the seat facing the person pushing the
stroller, or with the seat facing forwards. If the seat
is facing the person pushing the stroller: before
folding it, lower the backrest completely; if the seat is
facing forwards: before folding the stroller raise the
backrest, and once it is folded, lower it. To fold the
stroller set the front wheels to their fixed position
and close the hood, if fitted. Lift the two levers of the
handles together and push downwards to release the
side tubes (fig_a-b), pull the central handle upwards
(fig_c) until the safety catches engage (fig_d). When
folded the stroller will stand upright without support.
26 TRANSPORT: the stroller can be carried by the central
handle, keeping the front wheels fixed (fig_a) or by
the side handle (fig_b).
27 REMOVABLE LINING: with the backrest in its raised
position, detach the two elastic loops on the back
(fig_a), extract the four tabs to the sides (fig_b) and
detach the Velcro from the armrests (fig_c).
28 Slip the side lining off the hood tabs (fig_a), undo
the two buttons at the sides of the backrest (fig_b),
detach the two elastic loops of the sack from the
footrest (fig_c), remove the leg divider strap from the
top (by pushing it up from under the seat) (fig_d).
GANCIOMATIC SYSTEM
25 Ganciomatic is a fast and practical system that allows
you to attach the Navetta or PrimoNido bassinet unit,
the Primo Viaggio car seat or the Pliko Switch seat to
the Ganciomatic Base of the chassis in one quick step.
Place the item on the Ganciomatic Base and press
down with both hands until it clicks into place.
Always apply the chassis or stroller brake before
attaching and removing products (refer to the
respective instruction manuals).
Check that the child transport unit is properly
attached.
ACCESSORY
30 BORSA CAMBIO. Diaper-Changing Bag with pad for
changing the baby. Attaches to the stroller.

SERIAL NUMBERS

31 Pliko Switch reports information as at the date of
manufacture of the product.
- 19 -