Using The Timer - Denon RCD-M33 Instrucciones De Operación

10

USING THE TIMER

The time and timer functions are incorporated in the CD receiver.
Timer Settings
Types of timer operations
EVERYDAY TIMER : Use this to turn the power on and standby at the same time every day.
ONCE TIMER : Use this to turn the power on and standby once.
SLEEP TIMER : Use this to set the power to turn standby after 10 to 90 minutes, in steps
of 10 minutes (operated from the remote control unit).
Notes on timer settings
• Be sure to set the current time beforehand.
• To listen to or record a radio program ("air check") using the timer, be sure to preset the station
beforehand. (Refer to "Presetting or naming radio station" on page 13.)
Power Failures
If the power cord is unplugged or there is a power failure, the settings of the current time and
once timer are erased and the time display will flash. If this happens, reset the current time and
the once timer.
Also check the timer and tuner presettings, and reset them if they have been cleared.
Checking the Settings
To check the timer settings, press the MENU/ SET button to select TIMER.
9 8
Next, press the or button to select EVERYDAY or ONCE TIMER, then press the
MENU/ SET and 9 / 8 button repeatedly to display in order: Timer Setting mode, Function
selection, (when in TUNER mode) the reception band and preset channel number, Timer On time,
Timer Off time and Timer ON/OFF. Press the MENU/ SET button again to return to the current
mode display.
Changing the Settings
Repeat the timer setting operation to erase the previous settings and set the new settings.
Clearing the Settings
Press the MENU/ SET button to select TIMER. Next, press the
EVERYDAY, then press the 2 (stop) button for at least 2 seconds while EVERYDAY is displayed
to clear the everyday timer settings.
Press the MENU/ SET button to select TIMER. Next, press the
2
ONCE, then press the (stop) button for at least 2 seconds while ONCE is displayed to clear the
everyday timer settings.
Note on Setting the Timer
If the time set with the timer is reached while the system power is on, the operation switches to
the operation set by the timer.
Turning the Timer Off
Follow the steps for "to turn on or turn off EVERYDAY/ONCE timer feature" to turn off the
EVERYDAY/ONCE timer mode.
NOTE:
• Be sure to set the power to the standby mode when using the timer.
Setting the Current Time
The time is displayed in the 12-hour mode.
Example: Setting to 9:30 p.m.
Press the CLOCK button and select the
1
clock display mode.
Press the MENU/ SET button
for at least 1 second to select
the manual time setting mode.
2
(This cannot be set while the
clock is displayed in the
standby mode.)
Use the
3
button to set the hours.
9 8
/ button to select
4 Press the MENU/ SET button.
9 / 8 button to select
Use the
5
button
minutes.
Press the MENU/ SET button at the cue of a separate
clock or time service to start the clock.
6
• The time display stops flashing and the clock starts
running.
• If an RDS station offers a time service the time can be set by pressing the TIME/ DISPLAY and
MENU/ SET buttons on the remote control unit while that station is tuned in.
3, 5 2, 4, 6
Remote control unit
Main unit
Remote control unit
9 8
or
Main unit Remote control unit
Main unit Remote control unit
9 8
or
to set the
Main unit Remote control unit
ENGLISH
2, 4, 6
3, 5
3, 5
1
The hours place flashes. (If the
hours have already been set, that
number flashes.)
The hours place flashes.
The minutes place flashes. (If
the minutes have already been
set, that number flashes.)
minutes
The place flashes.
The display stops flashing and
the clock starts running from 00
seconds.
15