Braun MR 6550 M FP Manual Del Usuario página 8

• The blades are very sharp!
• Keep the appliance out of reach of children.
• The appliance is constructed to process
normal household quantities.
• Always unplug the appliance when it is left
unattended and before assembling, disas-
sembling, cleaning or storing.
• Before operating, check whether your
voltage corresponds to the voltage printed
on the bottom of the appliance.
• Especially when operating the handblender
attachment in hot liquids, do not immerse
the blender shaft into – or remove it from the
liquid while the appliance is switched on.
• Do not hold the motor part
)
whisk gearbox
immerse them in water.
(
• The beaker is not microwave-proof.
• Before operating the food preparation
{
attachment , make sure that the lid
interlock (2c) is properly clicked in and that
the pusher (1) is in place.
• Do not insert other tools than the pusher (1)
into the fi lling tube during processing.
• Always switch off the appliance before
removing the lid (2).
• The lid (2) can be cleaned under running
water, but do not immerse it in water, nor
clean it in a dishwasher.
• The bowl (4) is not microwave-proof.
• Braun electric appliances meet applicable
safety standards. Repairs or the replace-
ment of the mains cord must only be done
by authorised service personnel. Faulty,
unqualifi ed repair work may cause con-
siderable hazards to the user.
Description
!
Motor part
‚
On/off switch for variable speed
#
Turbo switch
$
Release buttons
%
Variable speed regulator
&
Blender shaft
Á
Wall mount
(
Measuring beaker with air-tight lid
)
Whisk gearbox
*
Whisk
{
Food preparation (FP) attachment
Setting the speed
When activating switch
speed corresponds to the setting of the
variable speed regulator
the speed setting, the faster and fi ner the
chopping results will be.
For maximum processing speed, press the
#
turbo switch . You may also use the turbo
switch for instant powerful pulses without
having to manipulate the speed regulator.
Depending on your application, we recom-
mend the following speed settings:
Handblender
Whisk
Food preparation
attachment
How to operate your handblender
The handblender is perfectly suited for
preparing dips, sauces, soups, mayonnaise
and baby food as well as for mixing drinks
and milkshakes:
1. Insert the motor part
&
shaft until it locks.
2. Introduce the handblender vertically into
the vessel, then press switch
„
switch .
3. To release the blender shaft after use,
‰
press buttons
You can operate the handblender in the
(
measuring beaker
other vessel. When blending directly in the
saucepan while cooking, take the pan from
the stove fi rst to protect the appliance from
overheating.
8
!
, nor the
under running water, nor
‚
, the processing
%
. The higher
1... turbo
3... 15
see speed tables in
picture sections A and B
!
into the blender
‚
or turbo
and pull it off.
, and just as well in any
How to operate your whisk
Use the whisk only for whipping cream,
beating egg whites and mixing sponges and
ready-mix desserts:
1. Insert the whisk
)
, then insert the motor part
gearbox until it locks.
2. Place the whisk in a vessel and only then,
‚
press switch
3. To release, press buttons
the gearbox. Then pull the whisk out of the
gearbox.
For best results ...
• use a wide bowl rather than the beaker
• move the whisk clockwise, holding it slightly
inclined
Whipped cream:
Only whip up to 400 ml chilled cream
(min. 30 % fat content, 4 – 8 °C).
Start with a low speed setting «1» and while
whipping, increase the speed to setting «15».
Egg snow:
Only whip up to 4 egg whites.
Start with a medium speed setting «7» and
while beating, increase the speed to setting
«15».
How to operate your food
preparation (FP) attachment
1 Pusher
2 Lid
2a Coupling for motor part
2b Filling tube
2c Lid interlock
3 Blade
4 Bowl
5 Anti-slip base (also serves as a lid)
6 Tool holder
6a Slicing tools (fi ne, coarse)
6b Shredding tools (fi ne, coarse)
Chopping
(see picture section
The blade (3) is perfectly suited for chopping
meat, cheese, onions, herbs, garlic, carrots,
walnuts, hazelnuts, almonds etc.
For chopping hard goods, use the turbo
„
switch .
N.B.: Do not chop extremely hard food, such
as nutmeg, coffee beans and grains.
Before chopping ...
• pre-cut meat, cheese, onions, garlic,
carrots, chillies
• remove stalks from herbs, un-shell nuts
• remove bones, tendons and gristle from
meet.
For best results, please refer to the speed
settings recommended in the processing
table.
a) Carefully remove the plastic cover from
the blade (3). Caution: the blade is very
sharp! Always hold it by the upper plastic
part. Place the blade on the centre pin of
the bowl (4) and give it a turn to lock into
place. Always place the bowl on the anti-
slip base (5).
b) Place the food in the chopper bowl.
c) Attach the lid (2) onto the bowl with the
interlock (2c) positioned next to the bowl
handle. To lock the lid, turn it clockwise so
that the interlock engages with a «click»
above the handle.
d) Insert the motor part
(2a) until it locks. Make sure the pusher is
in place.
e) To operate, press switch
motor part and take hold of the bowl with
your other hand.
f) After use, press buttons
motor part. Remove the pusher.
g) Pressing the lid interlock (2c), turn the lid
(2) counter-clockwise to unlatch it and lift it
up.
*
into the whisk gearbox
!
into the
to operate it.
‰
and pull off
A
with processing table i )
!
into the coupling
‚ „
or on the
‰
to remove the