Silverline 236576 Manual Del Usuario página 7

236576
Charging the battery
WARNING: Failure to follow the correct procedure when charging the
batteries will result in permanent damage.
1. Connect a discharged Battery (6) to the Battery Connector (7)
2. The red LED of the Battery Connector will illuminate to indicate a
battery has been connected. The red LED will illuminate even if the
Battery is already fully charged; it simply indicates a working battery
is connected. If the red LED does not illuminate, recheck the Battery is
correctly inserted in the charger. Remove any material that may have
fallen into the battery socket of the Battery Charger (8) and make sure
the contacts of both the Battery and the Battery Charger are clean,
untarnished metal and not damaged or bent. If the red LED still doesn't
illuminate there may be a fault with the Battery
WARNING: The LED does not show the charge status of the Battery, and the
Battery Charger does not switch itself off once the Battery is fully charged.
3. Remove the Battery from the Battery Charger after 3 – 5 hours and
disconnect the Battery Charger from the power supply
WARNING: Overcharging the Battery may reduce its capacity and shorten
its life. Excessive overcharging may destroy the Battery and/or Battery
Charger.
Further notes about battery charging:
• Except for the initial charge, the Battery should be fully discharged before
recharging to maximise lifespan of the Battery
• The Battery should be charged at ambient temperatures between 10 and
40°C (ideally close to 20°C)
• After charging, allow 15 minutes for the battery to cool before use
• Ensure that the Battery Charger (8) is disconnected from the mains
supply, and is stored correctly
• DO NOT leave batteries on charge for extended periods and NEVER store
batteries on charge
• Charge batteries close to when they will be used, ideally the previous day
or the same day
• Batteries can become faulty over time, individual cells in the battery
can fail and the battery could short. The charger will not charge such
batteries. Use the other battery to check correct functionality of the
charger and purchase a replacement battery
• The capacity of batteries will reduce over time. After 100 charge cycles
the length of time the battery will operate the tool and the maximum
torque performance of the drill will slightly reduce. This decline will
continue until the battery has minimal capacity after 500 charge cycles.
This is normal and not a fault with the battery
Fitting drill bits and accessories
WARNING: Always remove the Battery from the drill before attaching,
adjusting or removing accessories.
WARNING: Do not attempt to tighten drill bits (or any other accessory) by
gripping the front part of the Chuck (1) and switching the tool on. This can
lead to personal injury and can cause damage to the chuck.
WARNING: Never fit any attachment with a maximum speed lower than the
no load speed of the machine.
1. Open the Chuck (1) jaws by rotating the Chuck anti-clockwise (with
the Chuck facing the operator)
2. Place the drill bit or accessory into the Chuck correctly centralised
3. Tighten the Chuck jaws by rotating the Chuck clockwise
4. When the drill bit or accessory is securely fastened, carefully run the
machine to test that it is running centrally, smoothly and evenly. If the
bit is 'wobbling' or not running centrally, release the Chuck, check the
accessory for damage, correct its position, retighten and test again
Operation
Direction control
WARNING: NEVER change the direction of rotation while the tool is running.
• The direction of rotation can be set using the Forward/Reverse Switch (3)
• For anti-clockwise rotation, holding the drill in a normal operating
position, push the switch to the right
• For clockwise rotation, push the switch to the left
Note: When the Forward/Reverse Switch is in the central position, the drill
is locked and cannot be switched on. Use this setting as a safety feature to
prevent the drill from being switched on accidentally.
Torque control and mode selection
This drill is fitted with a Torque Selector (2). This controls the torque output
of the drill, enabling screws to be driven without the risk of damage to the
screw head or workpiece if set correctly. A clutch within the tool will slip
once the maximum torque is reached. There are 16 torque settings and a
drill mode
• The higher the torque setting chosen the higher the amount of torque
available. Select the correct setting for the screw size you are driving.
Over time you will get to know the required setting for the type and size
of screw
• The Torque Selector is numbered and has in between settings between
the numbers represented with dots to give the full 16 settings
• Rotate the Torque Selector ring to select the correct torque
• For drill mode, rotate the Torque Selector to the drill symbol. This will lock
the clutch out for maximum torque
Switching on/off
WARNING: Always wear adequate personal protection equipment when
setting up and operating this machine.
1. To start the drill, squeeze the Trigger (4)
Note: If the Trigger cannot be pressed down, check that the Forward/
Reverse Switch (3) is not set to its middle position, which locks the device
(see "Direction control").
2. The speed of the drill is controlled by the movement of the Trigger: the
further the Trigger is pressed down, the faster the drill will run
3. Release the Trigger to stop the machine
Note: A built-in work light will operate each time the trigger is pressed to
illuminate the work area.
Screwdriver use
Note: Use a universal bit holder when working with screwdriver bits. Only
mount screwdriver bits directly into the chuck if it is essential to access a
screw head. Use a bit holder at all other times.
• When driving screws NEVER use the machine in drill mode. This will
protect the motor by causing the clutch to slip rather than the motor to
stall when the screw is fully inserted in the workpiece and cannot rotate
any further
• Always adjust the drill to the appropriate torque setting (see "Torque
control")
Note: If in doubt about which torque setting best suits the application, start
with a low setting and increase, should more torque be required (e.g. if the
screw is not being driven far enough into the workpiece).
Drilling wood
• Select drill mode with the Torque Selector (2)
• Ensure that drill bits are suitable for wood, and are within the maximum
capacity of this machine (see "Specifications")
WARNING: DO NOT inhale wood dust. Wear adequate breathing protection.
Some wood dusts may be toxic.
Drilling metal
• Select drill mode with the Torque Selector (2)
• Ensure that drill bits are suitable for the grade of metal being drilled and
are within the maximum capacity of the machine (see "Specifications")
• To ensure accuracy, mark the intended hole position using a hammer
and centre punch
www.silverlinetools.com
Drill Driver 12V
7