Functioning Of Outdoor Sirens; Third Part - Control Unit Functioning; Installer-User Code - User Operations: Arming/Disarming - SILENTRON SILENYA HT 5500 Manual Del Usaurio

Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

D) Temperature control: the control unit can signal an anomalous temperature with an sms, below 5°C and above 70°C. 2.2.6)
2.3) FUNCTIONING OF THE SILENTRON SIRENS - ALSO SEE SPECIFIC MANUAL
The control units control the indoor and outdoor sirens via radio or wire (5500-5501 models). Those via radio function as follows:
a) Indoor sirens: they emit an arming (partial/full 3 Beeps) and disarming (just one Beep) acoustic signal, the intensity of which can be
regulated to zero. The signal is set off for 3 minutes in the case of a general, tamper or panic alarm. panic alarm.
b) Outdoor sirens: they emit an arming (partial/full 3 Beeps) and disarming (just one Beep) acoustic signal, the intensity of which can be
regulated to zero and they flash at the same time. The sirens activate for 3 minutes in the case of a general, tampering or panic alarm after a
pre-alarm period of about 10 seconds, during which an intermittent acoustic signal is emitted. This delay, which cannot be changed, is intended
to prevent disturbance if one forgets to disarm the system. In the case of OUTSIDE ALARM programming the outdoor sirens are not triggered,
but the pre-alarm condition continues for up to 3 minutes or a recorder dissuasive message is played, if equipped with vocal board code 5930.

3.0) THIRD PART - CONTROL UNIT FUNCTIONING

3.1)
SECURITY PROTECTION – USER CODE – INSTALLER CODE
The control unit is provided with a factory code "0 0 0 0" which allows access to the programming procedure. During installation it is necessary
to change this code, programming other two ones: USER code and INSTALLER code. These codes must be different from the arming/disarming
codes.
If these two codes are forgotten, the control unit must be disconnected. Warning: tamper alarm when opening ! When panel will be reconnected,
the procedure restarts by entering the factory code: this operation does not cancel any programming already performed.
a) INSTALLER CODE: from 4 to 8 digits, which allows access to all programming but not operations.
b) USER CODE: from 4 to 8 digits, allows the following functions
placing the control unit in TEST mode for testing or battery change.
reading the EVENTS MEMORY
programming/modification of listed telephone numbers (see third part)
recording/modification of all vocal messages (see third part)
addition/deletion of remote controls and/or numeric arming/disarming codes (see third part)
modification of supplementary wired key function (see third part)
modification of certain SETTINGS: Exclusion of radio or wired detectors (sensors) – Clock/date setting – Change of user code – Change of
daylight-saving time – Change of display back-lighting – Regulation of vocal message volume - Change of automatic forced arming –
Control unit firmware version check – Remote management access code change.
Attention! Careless with the USER code can limit the efficiency of the entire system, therefore, it is advisable to be informed on the various
functions before making any changes or have the installer carry out these operations, which can also be performed from a distance by remote
assistance.
3.2) USER OPERATIONS
NORMAL SITUATION OF THE CONTROL UNIT
13 / 02 / 09
17,00
DISARMED
_ ▄ █ █
3.2.1) ARMING - DISARMING USING THE CONTROL UNIT KEYPAD (VISUAL, VOCAL CONFIRM OR 3 BEEPS)
13 / 02 / 09
17,00
DISARMED
_ ▄ █
13 / 02 / 09
17,00
ARMED
A B C _ ▄ █
3.2.2) MANOEUVRES WITH REMOTE CONTROLS AND/OR ADDITIONAL KEYPADS
FULL ARMING (VOCAL CONFIRM OR 3 BEEPS)
Supplementary keypads: enter the numerical code and then press the red key
Remote controls: press the red key
PARTIAL ARMING (vocal confirm or a long Beep)
Supplementary keypads: enter the numerical code, by pressing A, B, C exclude the zones that are not to be armed and then press the red key
Remote controls: press the white key to arm zones A+B (for other solutions see the remote control instructions)
DISARMING (vocal confirm or a Beep)
Supplementary keypads: enter the numerical code and then press the green key
Remote controls: press the green key
SILENTRON spa – 10139 – Via Sagra S.Michele 25 Torino - ITALIA
DATE
HOUR
STATUS
GSM FIELD
ARMING
Enter a 5 digits keyboard code
DISARMING
Enter a 5 digits keyboard code
and press green button
Date and hour must be right to guarantee correct operations and memory:
these are settable by menu SETTINGS.
GSM field is showing in 5500 model only because in 5501 the GSM Phone
is normally OFF
ARM GROUPS:
A B C
13 / 02 / 09
17,00
DISARMED
_ ▄ █
COPYRIGHT SILENTRON DS5500/1/2/3XC100120GM
Select the groups you don't want
arming by pressing 1,2,3, and
press red button.
For full arming press red button
In the last armed/disarmed period
some events might be stored in
memory: in this case a vocal message
will inform you about after A/D
25

Publicidad

Tabla de contenido
loading

Productos relacionados para SILENTRON SILENYA HT 5500

Este manual también es adecuado para:

Silenya ht 5501Silenya ht 5502Silenya ht 5503Silenya ht 5500

Tabla de contenido