General Safety Rules - Evolution EVO42 Manual De Instrucciones

GB
Operating Instructions
Read instructions before operating this tool.
3 www.evolutionsteel.com
IMPORTANT
GB
Please read these operating and safety instructions
carefully and completely. For your own safety,
before using this equipment check that the voltage
is correct and that all handles and parts are firmly
secured. If you are uncertain about any aspect of
using this equipment contact your distributor.
Please Keep These Instructions
SPECIFICATIONS GB
Model EVO42 Specifications
Motor (230v or 115v 50/60 Hz) (Watts): 1200
Maximum Cutter Diameter: 1-5/8" (USA)
42mm (UK/EU)
Maximum Cutting Depth: 2" 50mm
RPM No Load (min-1): 450
Recommended Maximum Duty Cycle (Minutes): 30
Weight: 24lb 10.9kg
Max Dimensions (Rack Fully Raised):
22-7/8"x12-5/8"x7-1/16" 580x320x180
Min Dimensions (Rack Fully Lowered):
13-3/8"x12-5/8"x7-1/16" 340x320x180
Magnet Dimensions:
7-1/16"x3-1/2"x 1-1/2" 180x90x40
Magnetic Adhesion: 3360lb 1500kg
Cutter Retainer Internal Diameter: 3/4" 19mm
Weldon Shank
Standard Equipment Supplied With Unit: 1 Coolant
Tank, 1 Coolant Pipe, 1 Guard, 1 Hex key 2.5mm,
1 Hex Key 4mm, 1 Hex Key 3mm, 3 Handles, 2
Butterfly Screws, 2 Spring Washers, 1 Strap, Carry
Case.

GENERAL SAFETY RULES

GB
Ear and eye protection MUST be worn
while operating this equipment. Do
NOT touch the cutter while it is in
motion. Always follow the Personal
Protection Equipment (PPE) recom-
mendations while operating this tool.
This machine is designed specifically for drilling
holes in soft steel using the appropriate cutters and
accessories. It should NOT be modified and / or
used for any application other than for which it was
intended, including powering other equipment.
Ensure that the total work area can be viewed from
the operating position. Use barriers to keep people
away. Do not operate the tool in explosive environ-
ments – power tools create sparks that may ignite
flammable materials or gases. Do not operate the
tool in damp or wet conditions or areas, as electric
shocks may result. Always use both hands to oper-
ate the tool. Always ensure that the material you
are working on is securely clamped.
• This tool is equipped with an approved cord and
plug for its intended Country of use. The green and
yellow conductor in the cord is the grounding wire,
never connect this to a live terminal.
• Remove plug from power supply before replace-
ment of the cutter, making adjustments or other
maintenance work.
• We recommend the use of genuine Evolution
supplied cutters.
• Inspect the machine and cutter before each use
and do not use deformed, cracked, worn or other-
wise damaged cutters.
• Ensure the cutter is correctly mounted and do not
stop by hand.
• Do not use cutters that do not comply with the
characteristics specified in these instructions.
• Ensure that the guide bar and clamp lever
(secondary slide) are correctly adjusted before each
use. This is essential for proper and safe operation
of the machine.
• Always keep the power cord away from moving
parts of the tool.
• When you put the tool away, switch off the motor
and ensure that all moving parts have come to a
complete standstill.
• Never use the tool without the original protection
guard system.
www.evolutionsteel.com
EVO42
SPECIFIC SAFETY RULES & SYMBOLS
GB
Machine Set Up: Changing Cutters
To insert a cutter, first insert the pilot pin. Then
slide the cutter into the arbor, align the two flats
with the locking screw(s) and tighten securely with
the supplied hex wrench. CAUTION: Ensure that
the locking screw is on a flat of the cutter and not
just against the rounded shank. To remove cutter,
reverse the procedure. Ensure that the coolant feed
tap is on and coolant feeds properly by pushing the
pilot pin. If it feeds too quickly or slowly, adjust
the tap accordingly. Keep the tap closed when not
in use.
Symbol Description
V Volts
A Amperes
Hz Hertz
min Minutes
~ Alternating current
no no load speed
Double Insulated
Read Instructions
Wear eye Protection
Wear ear protection
Wear Boots
4