Briggs & Stratton Vanguard 580000 Manual Del Operario página 7

How To Check/Add Coolant
WARNING
Severe thermal burns can occur by escaping steam or hot coolant.
DO NOT remove radiator cap or reservoir cap if engine is warm or running.
•
Stop engine and allow it to cool before removing radiator cap or reservoir cap
•
and before changing or adding coolant.
1. Before operating, check the coolant level. The coolant level must be between the
FULL and the LOW/ADD marks on the coolant reservoir. If the coolant level is low,
add a 50/50% coolant mixture of phosphate-free antifreeze and tap water to the
reservoir.
2. To remove the reservoir cap after engine is cool, place a thick cloth over the reservoir
cap. Slowly turn the reservoir cap counterclockwise to remove.
3. If the reservoir is dry, then add coolant to both the reservoir and to the radiator. See
the equipment manual for location, operation, and maintenance of the coolant
reservoir and the radiator.
4. To remove the radiator cap after engine is cool, place a thick cloth over the radiator
cap. Slowly turn the radiator cap counterclockwise to the first stop. If pressurized
steam escapes from the cap, stand back to avoid injury. After all pressure is
released, push down and turn the radiator cap counterclockwise to remove.
Gauges And Lights
The gauges and lights shown are typical and represent various options that can be used.
See the equipment manual for location and operation of gauges and lights.
Coolant Temperature Gauge
Indicates coolant temperature when the electric start switch is in
the ON position.
Normal range 80º -- 90º C (175º -- 195º F)
Dangerous range above 105º C (220º F)
Hour Meter Gauge
Indicates the total number of operating hours.
Fuel Gauge
Indicates the fuel remaining in the fuel tank. To minimize condensation,
keep the fuel tank full.
Temperature Light
If the temperature light comes on, the engine is overheating. Stop the
engine and check the coolant level (see the How To Check Coolant
section). Check the radiator for debris that could restrict air flow.
Ignition Light
When the electric start switch is turned to the ON position, the ignition light
should be on. When the engine is running, the ignition light should go out.
If the ignition light is out when then electric start switch in the ON position, check for a
blown fuse.
Engine Oil Pressure Light
When the electric start switch is turned to the ON position, the engine oil
pressure light should be on. When the engine is running, the engine oil
pressure light should go out. If the engine oil pressure light comes on when the engine
is running, immediately stop the engine. First, check the oil level (see the How To
Check/Add Oil section). Next, check the electrical system.
Charge Light
When the electric start switch is turned to the ON position, the charge light
should be on. When the engine is running, the charge light should go out. If
the charge light comes on when the engine is running, check the electrical system.
How To Start The Engine - Figure 5
WARNING
Fuel and its vapors are extremely flammable and explosive.
Fire or explosion can cause severe burns or death.
When Starting Engine
Ensure that spark plug, muffler, fuel cap and air cleaner (if equipped) are in
•
place and secured.
Do not crank engine with spark plug removed.
•
If engine floods, set choke (if equipped) to OPEN/RUN position, move throttle
•
(if equipped) to FAST position and crank until engine starts.
en
WARNING
Starting engine creates sparking.
Sparking can ignite nearby flammable gases.
Explosion and fire could result.
If there is natural or LP gas leakage in area, do not start engine.
•
Do not use pressurized starting fluids because vapors are flammable.
•
WARNING
Engines give off carbon monoxide, an odorless, colorless, poison gas.
Breathing carbon monoxide can cause nausea, fainting or death.
Start and run engine outdoors.
•
Do not start or run engine in enclosed area, even if doors or windows are open.
•
NOTICE: This engine was shipped from Briggs & Stratton without oil. Before you start
the engine, make sure you add oil according to the instructions in this manual. If you
start the engine without oil, it will be damaged beyond repair and will not be covered
under warranty.
Note: Some engines and equipment have remote controls. See the equipment manual
for location and operation of remote controls.
1. Check the oil level. See the How To Check/Add Oil section.
2. Make sure equipment drive controls, if equipped, are disengaged.
3. Turn the fuel shut-off valve (A), if equipped, to the on position (Figure 5).
4. Move the throttle control (B) slightly past the slow
5. Turn the electric start switch (D) to the on/start position (Figure 5).
NOTICE: To prolong starter life, use short starting cycles, not to exceed 15 seconds
per minute. Extended cranking can damage the starter motor.
6. If the engine does not immediately start, pull out the choke control (C), if equipped, to
the choke position.
Note: Choke is usually unnecessary when restarting a warm engine.
7. As the engine warms up, move the choke control (C) to the run
How To Stop The Engine - Figure 5
WARNING
Fuel and its vapors are extremely flammable and explosive.
Fire or explosion can cause severe burns or death.
Do not choke the carburetor to stop engine.
•
1. Move the throttle control (B) to the slow
the off position (Figure 5). Remove the key and keep in a safe place out of the reach
of children.
2. After the engine stops, turn the fuel shut-off valve (A), if equipped, to the closed
position.
Maintenance
We recommend that you see any Briggs & Stratton 3/LC Authorized Dealer for all
maintenance and service of the engine and engine parts.
NOTICE: All the components used to build this engine must remain in place for proper
operation.
position.
position.
position. Turn the key switch (D) to
7