Setting Parameters - grandimpianti WR-EC 8 Instrucciones Para La Instalación Y Para El Uso

Figure 2
A prewash compartment (when scheduled
by the wash cycle selected)
B main wash compartment
C compartment for other products to be
added during the last rinse
Then select water level, which ranges
between the factory setting (calculated
following the maximum laundry load) and a
20% reduction that may apply to partial
loads or economy cycles.
Start the program pressing the green
"START" push-button, which is on the
control panel, on the right.
The door will automatically be locked and
cycle progress will be shown by the leds on
the left of the control panel (see 7.1).
The push-button causes the timer to start
its countdown to the end of the cycle, but
since the displayed cycle length depends
on real operating conditions, the effective
cycle time may not correspond.
Each time the push-buttons are pressed the
machine will beep shortly and it will beep
for 15 seconds at the end of the cycle. It is
however possible to stop the buzzer by
pressing the "_" push button or even inhibit
the buzzer altogether through programming
(see 7.3, function F5).
How to change a cycle in progress
If a wrong cycle has been started it is possible
to change the selection within the first two
minutes of operation. The display showing
the cycle number actually blinks for two
minutes after cycle start, to indicate that it is
possible to change the selection by pressing
the SEL push-button. After the SEL button
is pressed the next cycle will start and again
it will be possible to switch to the next
selection until the desired cycle is reached.
Cycle change occurs quickly after the SEL
push-button is pressed and repeated starts
and stops are avoided.
Alarm and fault signalling
When faults arise (voltage drop,
overtemperature, water level error) the
washing machine notifies the user by a
number of alarms that appear on the front
panel DISPLAY. All alarm details are dealt
with in the"ALARMS" chapter.
How to correct tub water level reading
Under normal conditions, water level reading
needn't be corrected, but when special
installation factors like elevation ask for it, it
is possible to set the zero level value in the
tub as follows:
1) Open the door.
2) Check that the tub is empty visually.
3) Hold the "+" and "-" keys down
simultaneously for at least 5 seconds.
4) The DISPLAY will read "CA LI b".
Figure 3
5) Confirm the value read by the card
pressing the PROG push-button.
6) The BUZZER will give out a beep and
the DISPLAYS will return to their
normal functions.
If the water level is corrected, the procedure
has been carried out correctly. Otherwise the
machine will keep the zero value previously
stored
7.2 CYCLE STEPS
The leds on the right part of the control
display indicate the various cycle steps, i.e.
from top to bottom:
Figure 4
1. YELLOW LED: STOP – The wash
cycle is over or the machine has just
been switched on
2. GREEN LED: PREWASH – Prewash
step underway (when scheduled)
3. GREEN LED: WASH - Wash step
underway
4. GREEN LED: RINSE 1/RINSE 5 –
Rinse underway (any between 1 and 5)
18
5. GREEN LED: SPIN – Final or
intermediate spin underway (blinks
when slowing down)
The leds blink when the machine is going
through a transitional intake or drain stage.
The intermittence stops when the machine
has reached the next step.
As soon as the cycle is over the YELLOW
LED goes on and the door is automatically
unlocked: then it will be possible to open the
door using the handle and pick the clean
laundry.
CAUTION! Never force the door open.
Open by hand only after it has been
unlocked.
At any rate, before opening the door make
sure that the drum has stopped, the water has
been drained and the temperature inside the
drum is below 40°C (take a look at the
temperature display). Should a potential drop
occur, open the door by pulling the manual
puller downwards. To reach the manual puller
it is necessary to unscrew and withdraw the
machine's lower front panel. After the door
has been unlocked manually, open it using
the handle as explained above and then put
the panel back in place.

7.3 SETTING PARAMETERS

Besides the "START" and "ECONOMY"
push-buttons, the machine has 4 more buttons
for cycle selection and special functions (see
6.1).
With the door closed, before the cycle is
started, the programming mode can be
entered by pressing the "PROG" push-button.
The time display will then blink "Pr" and the
remaining two displays will go off.
Figure 5
Pressing "PROG" again will cause the display
to read "F1" (on the time display), which