Broan SmartSense SQTXE080 Manual De Usuario página 4

Sistema de ventilación inteligente

Ocultar thumbs

Tabla de contenido

Idiomas disponibles

resToring power To conTrol

Control stores all settings in nonvolatile memory; so they

are not lost when power is removed. After power loss,

control will automatically return fan to its state (on or off)

before power was interrupted.

how To resTore conTrol facTory seTTings

This "Restore" procedure clears control's nonvolatile

memory. It returns control to how it was shipped from

factory. All links are removed and any Feature selection is

turned off.

Links are unique for each device pair. If one end of the

link is removed, it is important to remove the other end.

"Restore" only removes links within the particular control.

Other link-end needs to be removed in other control.

CAUTION: Master must be "Restored" if any Slave control

is "Restored" or if any Slave control is removed from

System. Master and all Slave links must be reestablished

using "How To Link SmartSense

1. Remove power from control's "brain" by either: (a) turn

circuit breaker off or (b) pull SET button until it stays

extended by itself.

2. Wait 15-seconds.

3. Press and hold SET button.

4. For option (1a), turn circuit breaker on while SET button

is pressed. For option (1b), push in and press SET button

in one motion.

LED should be on while SET button is pressed.

5. Continue holding SET button for 3-seconds and then

release it.

LED should turn off.

warranTy

Broan-Nutone warrants to the original consumer purchaser of its products that such products will be free from defects in materials or workmanship for a period of one year from

the date of original purchase. tHeRe ARe NO OtHeR WARRANtIeS, eXPReSS OR IMPLIeD, INCLuDING, But NOt LIMIteD tO, IMPLIeD WARRANtIeS OF MeRCHANtABILItY OR FItNeSS

FOR A PARtICuLAR PuRPOSe.

During this one-year period, Broan-Nutone will, at its option, repair or replace, without charge, any product or part which is found to be defective under normal use and service.

tHIS WARRANtY DOeS NOt eXteND tO FLuOReSCeNt LAMP StARteRS, tuBeS, AND FuSeS. this warranty does not cover (a) normal maintenance and service or (b) any products or

parts which have been subject to misuse, negligence, accident, improper maintenance or repair (other than by Broan-Nutone), faulty installation or installation contrary to recom-

mended installation instructions.

the duration of an implied warranty is limited to the one-year period as specified for the express warranty. Some states do not allow limitation on how long an implied warranty

lasts, so the above limitation may not apply to you.

BROAN-NutONe'S OBLIGAtION tO RePAIR OR RePLACe, At BROAN-NutONe'S OPtION, SHALL Be tHe PuRCHASeR'S SOLe AND eXCLuSIVe ReMeDY uNDeR tHIS WARRANtY. BROAN-

NutONe SHALL NOt Be LIABLe FOR INCIDeNtAL, CONSeQueNtIAL OR SPeCIAL DAMAGeS ARISING Out OF OR IN CONNeCtION WItH PRODuCt uSe OR PeRFORMANCe. Some states

do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation may not apply to you.

this warranty gives you specific legal rights, and you may also have other rights, which vary from state to state. this warranty supersedes all prior warranties.

to qualify for warranty service, you must (a) notify Broan-Nutone at the address or telephone number below, (b) give the model number and part identification and (c) describe the

nature of any defect in the product or part. At the time of requesting warranty service, you must present evidence of the original purchase date.

Broan-Nutone LLC Hartford, Wisconsin www.broan.com 800-558-1711

System" procedure.

BROAN-NutONe ONe YeAR LIMIteD WARRANtY

models ssQTXe080 • ssQTXe110

6. After less than 5-seconds, fan and LED turn on for 1 to

2-seconds and then turn off; which confirms "Restore"

was successfully accomplished.

7. If control does not respond as described, start process

over with step 1.

how To change conTrol color

An almond paddle/frame assembly is included.