Remotec Z-URC 550 Instrucciones De Operación página 4

Add a device to the network
1. Enter Z-Wave advanced setup by pressing the Conf key then the OK light
turns on.
2. Press Add once, the OK light flashes once and stays on.
3. Press Device once, the OK light flashes once and stays on then the step 3
light will flash slowly.
4. Press the button on desired Z-Wave device the OK light flashes once and
turns off indicating set up is successful.
Delete a device from the network
1. Enter Z-Wave advance setup by pressing the Conf key then the OK light
turns on.
2. Press Delete once, the OK light flashes once and stays on.
3. Press Device once, the OK light flashes once and stays on then the step 3
light will flash slowly.
4. Press the button on target Z-Wave device, the OK light flashes once and
turns off indicating the device was successfully deleted.
Setting up an association within a group
Associations are used to set up one node to automatically contact another
node when the first is triggered. For example you can set up a door sensor
(primary node) to turn on the light (secondary node) when the door has been
opened.
Add device to an association group
1. Enter Z-Wave advance setup by pressing the Conf key then the OK light
turns on.
2. Press Add once, the OK light flashes once and stays on.
3. Press Assoc once the OK light flashes once then stays on then the step 2
light flashes slowly.
4. Select a group number from 1 to 16 (1~8 or SHIFT 1~8), OK flashes once
and stays on then the step 3 light will flash slowly.
5. Press the button on secondary Z-Wave device the OK light flashes once
then keeps flashing slowly.
6. Press the button on the primary Z-Wave device then the OK light flashes
once and turns off indicating the two devices were successfully associated.
Remove a device from an association group
1. Enter Z-Wave advance setup by pressing the Conf key then the OK light
turns on.
2. Press Remove once, the OK light flashes once and stays on.
3. Press Assoc once the OK light flashes once then stays on then the step 2
light will flash slowly.
4. Select a group number from 1 to 16 (1~8 or SHIFT 1~8), the OK light
flashes once and stays on then the step 3 light will turn off.
5. Press the button on the secondary Z-Wave device, the OK light flashes
once and stays on.
6. Press the button on the primary Z-Wave device then the secondary device
will no longer be associated with the primary device. The step 3 button will
turn off and the OK light will flash once then turn off indicating the device
was removed from the association group.
6
GB
Delete an association group
1. Enter Z-Wave advance setup by pressing the Conf key then the OK light
turns on.
2. Press Delete once, the OK light flashes once and stays on.
3. Press Assoc once the OK light flashes once then stays on then the step 2
light will flash slowly.
4. Press the group you wish to delete a primary device from 1 to 16 (1~8 or
SHIFT 1~8) OK flashes once and stays on then the step 3 light will flash
slowly.
5. Press the button on target primary Z-Wave device, the OK light will flash
once then turn off indicating the primary device and all associated devices
were deleted from the group.
How to set up and use a scene
Scenes are used for setting up multiple devices in the same way as a group
but in addition to groups, scenes also control dimmer lights that you can set to
different levels depending on the situation. For example you can have the
scene set to low brightness for watching a movie or going to bed or
alternatively set the lights brighter when reading or working. After the scene
has been programmed it will work with the corresponding ON OFF key on the
top side of the remote. For example the scene programmed into group 1 will
be activated with the first set on ON OFF buttons on the topside of the remote.
Add a device to a scene
1. Enter Z-Wave advance setup by pressing the Conf key then the OK light
turns on.
2. Press Add once, the OK light flashes once and stays on.
3. Press Scene once the OK light flashes once then stays on then the step 2
light will flash slowly.
4. Select a key from 1 to 16 (1~8 or SHIFT 1~8), the OK light flashes once
and stays on then the step 3 light will flash slowly.
5. Press the button on desired Z-Wave device, the OK light flashes once and
stays on then the step 3 light will also remain on.
6. Press and hold the button on the dimmer, until the dimmer is set to the
desired brightness level.
7. Press Scene once, the OK flashes once then turns off and the step 3 light
turns off indicating the device has been successfully added.
Remove a device from a scene
1. Enter Z-Wave advance setup by pressing the Conf key then the OK light
turns on.
2. Press Delete once, the OK light flashes once and stays on.
3. Press Scene once, the OK light flashes once and stays on then the step 2
light will flash slowly.
4. Select a key from 1 to 16 (1~8 or SHIFT 1~8), the OK light flashes once
and stays on then the step 3 light will flash slowly.
5. Press the button on desired Z-Wave device, the OK light stays on then
flashes once and turns off indicating that the device was successfully
removed.
Delete a scene
1. Enter Z-Wave advance setup by pressing the Conf key then the OK light
turns on.
2. Press Delete once, the OK light flashes once and stays on.
3. Press Scene once, the OK light flashes once and stays on then the step 2
light will flash slowly.
4. Then press the scene you wish to delete from 1 to 16 (1~8 or SHIFT 1~8)
the OK light will flash once then turn off indicating the group has been
deleted.
GB
7