Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
Punch Through Volume
Punch through volume allows you to operate volume up and down without
having to switch the device modes repeatedly even when your
other operating modes.
To activate the punch through volume setting:
1. Press desired Device Mode Key (e.g. TV).
2. Press and Hold "VOL +" key.
3. While still holding the
"VOL +"
key press desired Device Mode Key (e.g.
SAT).
4. Release
"VOL +"
and the green indicator flashes once, now by pressing the
"VOL +"
key while in TV mode the remote will act as if pressing the
key in SAT mode.
To deactivate the punch through volume setting:
1. Press desired Device Mode Key (e.g. TV).
2. Press and Hold "VOL -" key.
3.
While still holding the
"VOL -"
key press desired Device Mode Key (e.g.
SAT).
4. Release "VOL -" (the green indicator flashes twice if the setting is
deactivated).
Macro Power
Macro Power allows you to turn two of your A/V equipment on/off
simultaneously.
To activate the macro power setting:
1. Press desired Device Mode Key (e.g. TV).
2. Press and Hold " " key.
3. Press desired Device Mode Key (e.g. SAT).
4. Release " " (the green indicator flashes once if the setting is activated).
To deactivate the macro power setting:
1. Press desired Device Mode Key (e.g. TV).
2. Press and Hold " " key.
3. Press desired Device Mode Key (e.g. SAT).
4. Release " " (the green indicator flashes twice if the setting is deactivated).
7
ADVANCED OPERATION FOR AV EQUIPMENT
Secondary Function
1. Some keys are able to access 2 functions through the use of the shift key.
2. To use a buttons secondary function, press the shift key then the next
button pressed will perform its secondary function after which the buttons
will return to their primary functions.
3. You can access the shift lock mode by pressing and holding the shift key for
3 seconds after which all buttons pressed will use their secondary function.
Pressing the shift key again will end the shift lock.
TM
IR Boost Mode (only Z-URC 550)
By activating the boost switch in the battery compart
send out 3 IR beams instead of 1 IR beam. Effectively tripling the
your IR signal.
Note: The range of your IR beam along with the angels will be increased but
will also consume more power from the batteries.
16
GB
TM
Z-URC
is in
"VOL +"
TM
ment your Z-URC
will
power of
Restore Factory Settings
1. Hold down "CH +" and "VOL -" keys on the remote simultaneously for 3
seconds until you the indicator lights up and stays lit.
2. Enter the reset code "9", "9", "9", "9". The indicator light goes out
immediately. All settings are now restored to factory default setting.
8
MAINTENANCE
TM
1. Do not expose your Z-URC
to dust, strong sunlight, humidity, high
temperatures or mechanical shocks.
2. Do not use old and new batteries together as old batteries tend to leak.
3. Do not use corrosive or abrasive cleansers on your Z-URC .
4. Keep the unit dust free by wiping it with a soft, dry cloth.
TM
5. Do not disassemble your Z-URC , it contains no user-serviceable parts.
9
FREQUENTLY ASKED QUESTIONS
Universal remote control frequently asked questions
TM
Q: My Z-URC does not work at all!
A: Check your A/V device, if the device's main switch is turned off, your Z-
TM
URC cannot operate your device.
A: Check whether your batteries are inserted properly and are in the correct
+/- position.
A: Check whether you have pressed the corresponding device mode key for
your device.
A: If the batteries are low, replace the batteries.
Q:
If several Device Codes are listed under the brand of my A/V device,
how can I select the correct Device Code?
A:
To seek the correct Device Code for your A/V device, test the codes one by
one until most keys work properly.
Q:
My A/V equipment responds only to some of the commands.
A:
You have set a code for which only some commands work properly but
some do not. Try other codes until most keys work properly. You can also
use the learning function to learn additional keys. (only Z-URC 550)
17
GB
TM
TM
Publicidad
Tabla de contenido
