Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
5. Press the same desired device mode key again as in step 2 above. (e.g. TV)
6. Hold down "CH +" & "VOL -" simultaneously for 3 seconds until the green
TM
indicator lights up, and your Z-URC is ready to start searching.
TM
7. Aim the Z-URC
at your device (e.g. TV), press the "
repeatedly until the device has been turned off.
Once your device has been turned off, immediately press Device Mode
Key (e.g. TV) to lock in code and the indicator should go out.
* Simply repeat the above setup procedures to search for the Device Code
for your SAT/CBL, DVD or AUX. (Remember to press the correct Device
Mode Key and correct Magic Search Code in step 2-5 above)
IMPORTANT:
- If the power on/off function of your device is not infra-red controlled, you
need to follow steps 2 to 6 above and start searching:-
- Press "
" and another function key alternately until your device
responds to the expected function, then press the same Device Mode
Key (e.g. TV) to lock in the code.
e.g. Press "
" & "1" alternately, or;
Press "
" & "
" alternately.
Note:
- TV, VCR, DVD, CTV and other device codes can be searched for and
locked into any device modes. Simply press the corresponding device
mode key in step 2 & 5 and enter an appropriate Magic Search Code for
your DVD, CTV and other devices.
TM
- Each time you press the "
", the
Z-URC
will skip to the next code and
send out a POWER signal trying to turn off your device.
If you fail to stop pressing "
" when your device has been turned off,
turn your device on again immediately. Before the green indicator goes
TM
out, press "
"on the
Z-URC
to skip backward. Repeat step 7 above
and lock in the code.
- If the red indicator flashes six times after your pressing of "
are already at the last code of the library. Press "CH +" and "VOL -" to
TM
resume the
Z-URC
and repeat the above procedures carefully to
search again.
TM
By Learning Commands (only Z-URC 550)
TM
Your Z-URC is equipped with learning capability. This allows you to "teach"
TM
your Z-URC
certain functions from your original equipment remote. Please
follow the steps below.
1. Press the desired device mode key (e.g. TV).
2. Hold down "CH +" and "VOL -" on the Z-URC
seconds until the green indicator lights up.
3. Enter the learning code " ", "0", "0", "0". The green indicator light will flash
0
TM
once then stay lit. The Z-URC is now ready to learn.
TM
4. Place the Z-URC
and your device remote on a flat surface, aimed at
each other 1-3 inches apart.
5. Press a desired key once and release on the Z-URC
learn the command. The green indicator will flash once then stay lit.
14
GB
" key slowly and
" key, you
TM
simultaneously for 3
TM
which you want to
6. Press and keep holding the key on your original equipment remote which
you want to learn for a few seconds.
7. When the green indicator light flashes twice and stays lit continuously, the
command has been learned successfully and you can release the key on
your original equipment remote. If the red indicator light flashes six times,
it shows an error in the learning process. Adjust the position of both
remotes and repeat from step 5 again.
8. Repeat from step 5 to learn other key functions, or press the same device
mode key on step 1 (e.g.TV) to terminate the learning mode, the green
indicator light will flash twice and then go out immediately.
Note:
-
On step 5 if no key is selected for more that 8 seconds, the red indicator
light will flash six times and the learning mode will exit automatically.
-
On step 6, if no other remote signal is received for more than 8 seconds,
the red indicator light flashes six times and stays lit continuously, you
need to select a desired key again for learning as in step 5 on your Z-
TM
URC
.
-
Each function key will hold one command only, a new command to be
learned will automatically erase and replace the previous one.
-
If the green indicator light flash six times during the transference of
signals, the maximum 100 commands memory bank is full, press the
same device key again to resume normal operation.
-
All device mode keys, as well as the SHIFT keys cannot be used for
learning functions.
TM
6
OPERATING THE Z-URC FOR AV EQUIPMENT
Normal Operation
TM
Once you have set up the
Z-URC
for your A/V equipment, it works like your
original remote control. To operate, just aim it at your equipment, press an
appropriate device mode key and invoke the desired function by pressing a
TM
corresponding key on the
Z-URC
. The green indicator turns on during signal
transmission and as
Confirmation of
key touch.
Punch Through
Punch Through Channel
Punch through channel allows you to operate channel up and down without
having to switch the device modes repeatedly even when your
other operating modes.
To activate the punch through channel setting:
1. Press desired Device Mode Key (e.g. TV).
2. Press and Hold "CH +" key.
3. While still holding the "CH +" key press desired Device Mode Key (e.g. SAT).
4. Release "CH +" and the green indicator flashes once, now by pressing the
"CH +" key while in TV mode the remote will act as if pressing the "CH +"
key in SAT mode.
To deactivate the punch through channel setting:
1. Press desired Device Mode Key (e.g. TV).
2. Press and Hold "CH -" key.
3.
While still holding the "CH -" key press desired Device Mode Key (e.g. SAT).
4. Release "CH -" (the green indicator flashes twice if the setting is
deactivated).
15
GB
TM
Z-URC
is in
Publicidad
Tabla de contenido
