Additional Features - Remotec Z-URC 550 Instrucciones De Operación

3

ADDITIONAL FEATURES

There are a number of additional features included in the Z-URC
that allow you to replicate an additional primary or add a new secondary
controller to your Z-Wave network. Below is a summary and instructions on
using all the additional features.
Copying all network and device information to a secondary remote
controller
You can add a secondary remote to your network and copy all of your primary
remotes network and device information to the secondary remote by following
the steps below.
1. Enter Z-Wave Additional Feature Setup Mode by pressing and holding the
Conf and Remove keys for 3 seconds then the OK light will remain on.
2. Place the two remotes close to each other.
TM
3. Enter 8541 on the XpressZetup keypad the OK light will flash once after
you enter one digit and then will keep flashing after entering all 4 digits.
4. Make sure the target remote is set up to receive information. (Refer to the
target remotes user manual for more information)
5. When the replication has been completed the OK light flashes once slowly
and then turns off.
Note: If the replication is unsuccessful, the OK light turns off and the error
light will flash 6 times then turn off.
Copying only network information to a secondary remote controller
You can add a secondary remote to your network and copy all of your primary
remotes network information to the secondary remote by following the steps
below.
1. Enter Z-Wave Additional Feature Setup Mode by pressing and holding the
Conf and Remove keys for 3 seconds then the OK light will remain on.
2. Place the two remotes close to each other.
TM
3. Enter 8542 on the XpressZetup keypad the OK light will flash once after
you enter one digit and then will keep flashing after entering all 4 digits.
4. Make sure the target remote is set up to receive information. (Refer to the
target remotes user manual for more information)
Transferring all network and device information to an new primary
remote controller (primary shift)
You can transfer all of your remotes information to another remote so that it
will become the new primary remote. This is done by following the steps below.
1. Enter Z-Wave Additional Feature Setup Mode by pressing and holding the
Conf and Remove keys for 3 seconds then the OK light will remain on.
2. Place the two remotes close to each other.
TM
3. Enter 8361 on the XpressZetup keypad the OK light will flash once after
you enter one digit and then will keep flashing after entering all 4 digits.
4. Make sure the target remote is set up to receive information. (Refer to the
target remotes user manual for more information)
Transferring only network information to an new primary remote
controller (primary shift)
You can just transfer network information to another remote so that it will
become the new primary remote. This is done by following the steps below.
1. Enter Z-Wave Additional Feature Setup Mode by pressing and holding the
Conf and Remove keys for 3 seconds then the OK light will remain on.
2. Place the two remotes close to each other.
TM
3. Enter 8362 on the XpressZetup keypad the OK light will flash once after
you enter one digit and then will keep flashing after entering all 4 digits.
4. Make sure the target remote is set up to receive information. (Refer to the
target remotes user manual for more information)
8
GB
Replicating all network and device information from a primary controller
to this remote controller (aka learning mode)
TM You can have this remote
remotes
(1) Copy the settings from another Z-Wave remote control
(2) Can be include into existing Z-Wave Network and become a new primary
or secondary remote
(3) Can be exclude from the Z-Wave network
by following the steps below:
1. Enter Z-Wave Additional Feature Setup Mode by pressing and holding the
Conf and Remove key for 3 seconds then the OK light will remain on.
2. Place the two remotes close to each other.
3. Enter 8363 on the XpressZetup keypad the OK light will flash once after
you enter one digit and then will keep flashing after entering all 4 digits.
4. Make sure the primary source remote is set up to send information to your
TM
Z-URC remote control. (Refer to the target remotes user manual for more
information)
5. When the replication has been completed the OK light flashes once slowly
and then turns off.
Note: If the replication is unsuccessful, the OK light turns off and the error
light will flash 6 times then turn off.
CAUTION
!
Scene Controller Configuration Command and Association Command
If scenes are copied to a secondary controller using the replication function,
those scenes cannot be modified using the Scene Controller Configuration
and Association Commands. If modifications are desired, it is
recommended to delete all these scenes from the controller prior to using
the two aforementioned commands.
Listening mode (there are multiple usage by entering this mode)
- Version command class: To get application software version, the Z-Wave
protocol version and the supported Z-Wave command version of this
remote.
- Manufacturer command class: To get the manufacture ID, product type ID
and the product ID of this remote.
- Scene configuration command class: Home gateway can bundle a scene
ID to a group ID using this command.
- Association command class: To create and maintain associations in this
remote.
1. Enter Z-Wave Additional Feature Setup Mode by pressing and holding the
Conf and Remove keys simultaneously for 3 seconds then the OK light will
remain on.
2. Enter 8364 on the XpressZetup keypad the OK light will flash once after
you enter one digit and then will keep flashing after entering all 4 digits.
3. Listening mode will automatically exit after 1 minute of inactivity.
4. When exiting listening mode the OK light flashes once then turns off.
Note: The mode must not be exited during communication process with
another remote. Please wait for entire communication process to be
completed.
GB
TM
TM
9