Manual Release Mechanism; Electronic Programmer - Cardin Elettronica SL424E9CB Manual Del Usuario

INSTRUCTIONS FOR POSITIONING THE UNIT
7
- The geared motor unit has been assembled in the factory to be fitted
to the LEFT SIDE of the gate (internal view).
page 19).
All rights reserved. Unauthorised copying or use of the information contained in this document is punishable by law

MANUAL RELEASE MECHANISM

Manual release is carried out with the power to the motor interrupted
due to a power failure. To release the gate use the manual release key
supplied with the unit. The key should be kept inside the house in an
easily accessible place or stored with the unit itself.
8
A
To release the unit
A
the T-shaped pin, then rotate the key through 90 degrees in the direction
C
separate the gears from the motor allowing you to manually manoeuvre
the gate by pushing lightly on it.
To relock the unit
Follow the above instructions in reverse order rotating the key through
SCALA: 1:2
Description : Prodotti Technocity
Drawing number : DI0479
Sblocco motore
Product Code : SL????
Draft : P.J.Heath Date :
12-02-2007
CARDIN ELETTRONICA S.p.A - 31020 San Vendemiano (TV) Italy - via Raffaello, 36 Tel: 0438/401818 Fax: 0438/401831 Attention! Never use the manual release mechanism while
the gate is in operation.
Moving the gate manually will force the encoder to lose the
position of the gate. To reset the control, once the gate has
been relocked, you will need to give 3 or more movement
commands so that the gate leaf will reach the travel limit
enough times to position itself correctly.
Access to the electronic card
through 90° as shown in fig. 8.
Caution! Before opening the cover make sure that the
power has been switched off at the mains.

ELECTRONIC PROGRAMMER

Electronic programmer for a dc motor with an incorporated radio receiver
card, which allows the memorisation of 300 user codes
series transmitters.
The motor rotation speed is electronically controlled, starting slowly
and increasing in speed; the speed is reduced as it nears the travel
limit so as to enable a controlled smooth stop.
Programming is carried out using one button and allows you to set the
current sensor and the entire gate travel distance.
MdIR
F
G
9 0 ϒ
B
C
D
D
A
G
433.92 MHz
the closing and opening stages causes a brief (5 cm) travel
direction inversion then a block.
the programmer, release the gate (manual release mecha-
nism) and move it manually, checking that it moves smoothly
and has no unusual points of resistance.
1
This is indicated by the warning lights pre-flashing for 10
seconds, and by the symbol
automatic repositioning
ing system, which is used to block the motor in emergency
conditions; however this system is not active during the first
second of each manoeuvre.
Do not therefore attempt to physically block the door during
these stages.
If you need to check the status of the fuses, disconnect the
power supply to the programmer; reconnect it only after
having re-inserted the fuse.
The presence of the electrical input monitoring system does
not exclude the need to install photoelectric cells or other
safety devices which are foreseen by the local standards
and regulations in force.
The geared motor unit has been assembled in the factory
to be fitted to the left side of the gate. Read the paragraph
instructions for positioning the unit
For the correct operation of the programmer the incorpo-
rated batteries must be in good condition: the programmer
will lose the position of the gate in case of blackouts when
B
the batteries are flat, the alarm will sound and automatic
repositioning will take place .
Check the good working order of the batteries every six
and frequency rated on the data plate conform to those of
the mains supply.
contacts must be installed between the unit and the mains
supply.
the ends of cables which are to be inserted into the bind-
ing posts; use cables marked T min 85°C and resistant to
atmospheric agents.
both the wire and the insulating sheath are tightly fastened
(a plastic jubilee clip is sufficient).
ELECTRICAL CONNECTION 230 Vac
device wires.
230 Vac mains power
and the through the cable clamp
PS
- connect the live to post 1
- connect the earth to post 5
- connect the neutral to post 2 N
16
IMPORTANT REMARKS
before powering up
appearing on the display
Battery check
3 mm between the
230Vac
N L
TS
TS
L
-
9