General Information - Electrolux 32476 Manual De Instrucciones

1-3 THE ENVIRONMENT
1-3-1 Packaging
Packaging materials are environment friendly and can be stored
without risk, or burned in a special waste incineration plant.
1-3-2 Use
Our appliances offer high performance and effi ciency. To reduce
energy consumption, do not use the appliance empty or in
conditions that compromise optimum effi ciency.
1-3-3 Cleaning
In order to reduce the emission of pollutants into the environment,
clean the appliance (externally and when necessary internally)
with products that are more than 90% biodegradable (for further
information, see chap. 4)
2 – INSTALLATION
2-1 DIMENSIONS AND WEIGHT (FOR INFORMATION ONLY)
See picture
2-2 UNPACKING
Important!
Immediately check for any damage caused during transport.
Inspect the packaging before and after unloading.
• The forwarder is responsible for the goods during transport
and delivery.
• Make a complaint to the forwarder in case of visible or hidden
damage. Specify any damage or shortages on the dispatch
note.
• The driver must sign the dispatch note: the forwarder can reject
the claim if the dispatch note is not signed (the forwarder can
provide the necessary form).
2-3 LOCATION AND LAYOUT
!Always, place the machine on a strong, fl at, stable support.

GENERAL INFORMATION

• The appliance must be installed over a counter top. Please remove
the feet and fi x the appliance over the table by sealing it.
• The installation diagrams gives the overall dimensions of the
appliances and its position in space See
• The presentation diagram describes and locates each part of
the appliance. See
A. Lid
B. Handle
C. Control panel
D. Feet
E. Ventilation holes
F. Front top cover
G. Steam evacuation chamber
H. Upper heating plate and its locking system
I. Glass
J. Electro magnet
K. Cooking chamber
• The appliances are not designed for built-in installation. See
for minimal space required.
• Maintain an adequate distance between the appliance and
any combustible walls .
• Leave an adequate space between the appliance and any
side walls in order to allow subsequent servicing or maintenance
operations and its proper ventilation . See
• Before starting to use the appliance, check its perfect levelness
with a level.
HSPP GB 09 2008
2 5
5
1
1-3-4 Disposal
• For hidden damage or shortages becoming apparent only after
unpackaging, request the forwarder for inspection of the goods
within and no later than 15 days after delivery.
• Keep all the documentation contained in the packaging.
Remove the packaging and refer to chapter 1-3-1.
Take care when unpacking and handling of the machine to not
cause any shocks on itself.
Important!
Do not obstruct the vent holes of the appliance in any way
• Before plugging the appliance in, check:
- the compatibility of the plug in the country of use
- that the main switch, the power supply voltage and operating
frequency are suitable for the load of the appliance according
to the data plate
- Check the conformity of the electrical system with current
2
standards and ensure that the prescribed protection and sa-
fety devices are installed. The appliance must have a ground
connection in conformity with current standards. Carry out
the equipotential connection, in appliances where required,
by means of the special terminals marked with the symbol:
- check the compatibility of the data plate specifi cations with
the mains voltage and frequency.
Information on sound emissions: The functional components
of the appliances in question have a noise level not exceeding
70 dB (A).
Important!
Make sure that the plug of the appliance is reachable in any
working conditions.
CAUTION!
Do not locate appliance adjacent to any high heat or grease
producing piece of equipment, such as a range top, griddle,
fryer, etc., that could allow radiant heat to raise the exterior
temperature of the appliance.
CAUTION!
Do not use reducers, adapters or branches for the connection,
as they could cause false contacts with risk of dangerous
overheating.
5
3/9
Do not disperse in the environment.
Our appliances are manufactured using
more than 90% (in weight) recyclable
metals (stainless steel, iron, aluminium,
galvanized sheet, copper, etc.).
Make the appliance unusable by re-
moving the power supply cable and
any compartment or recess locking
mechanisms (when present) in order
to avoid the risk of someone being
trapped inside.