Descargar Imprimir esta página

Fender PRINCETON 65 DSP Instrucciones De Funcionamiento página 6

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

P P
r r
i i
n n
c c
e e
t t
o o
6
P P
r r
i i
n n
c c
e e
t t
o o
Your new Princeton
®
world–class Fender
®
tone and world–standard Fender
DSP technology:
• 65W of output power @ 8 ohms
• Digital Signal Processing
• 16 FX SELECTIONS
• Separate FX LEVEL control
P P
a a
n n
e e
l l
F F
u u
P P
a a
n n
e e
l l
F F
u u
A. INPUT - Plug your guitar in here.
The Normal channel controls (B-D) are operational when the
CH SELECT button
is out, or footswitch LED
B. VOLUME - Adjusts the loudness of the amplifier.
C. TREBLE - Adjusts the high-frequency tone.
D. BASS - Adjusts the low-frequency tone.
E. CHANNEL SELECT -
Button OUT
selects the Normal Channel
Button IN
selects the Drive Channel
The Drive channel controls (F–K), are operational when the
CH SELECT button
is in, or footswitch LED
F. DRIVE - Adjusts the distortion level.
conjunction with the Drive Channel VOLUME control
(H) to adjust the overall loudness of the amplifier.
G. CHANNEL INDICATOR -
LED OFF
Normal Channel is active
LED ON
Drive Channel is active
H. VOLUME - Adjusts the loudness of the amplifier in
conjunction with the DRIVE control (F).
I. TREBLE - Adjusts the high-frequency tone.
J. MID - Adjusts the mid-frequency tone.
K. BASS - Adjusts the low-frequency tone.
L. FX LEVEL - Adjusts the level of the selected effect.
M. FX SELECT - Selects the active effect (see next
page).
w w
w
w w
w . . f f e
e n
n d
d e
n n
® ®
® ®
6 6
5 5
D D
S S
P P
A A
m m
p p
n n
6 6
5 5
D D
S S
P P
A A
m m
p p
65 DSP amplifier delivers
n n
c c
t t
i i
o o
n n
s s
n n
c c
t t
i i
o o
n n
s s
is off.
is on.
Use in
e r
r . . c
c o
o m
m
l l
i i
f f
i i
e e
r r
l l
i i
f f
i i
e e
r r
• Selectable
Normal
®
independent volume and tone controls
• PRE-AMP OUT and POWER-AMP IN jacks
• FOOTSWITCH jack for use with a 2-button Fender
footswitch (optional); enables remote activation of:
(1) Channel Select, (2) Effects
Thank you for choosing Fender
Thank you for choosing Fender
—T
one, T
radition and Innovation—since 1946
—T
one, T
radition and Innovation—since 1946
N. PRE AMP OUT / POWER AMP IN - (1) Effects Loop
- Connect PRE AMP OUT to an effects device input,
then connect the effects device output to PWR AMP
IN. (2) Multiple Amps - Connect the primary unit's
PRE AMP OUT to the auxiliary unit's PWR AMP IN.
The primary unit is used to control all auxiliary amps.
(3) Recording or Reinforcement - Connect PRE
AMP OUT to sound equipment's input.
PRE AMP OUT includes onboard tone
shaping and DSP effects processing. Both jacks use
a TS (Tip-Sleeve) standard type plug for connections.
O. FOOTSWITCH - Connect a 2-button Fender
footswitch (optional) at this jack to enable remote
switching of CH SELECT and EFFECTS.
plugged
in,
corresponding panel controls.
P. POWER INDICATOR - Illuminates when the
amplifier is ON.
Q. POWER SWITCH - Switches the
amplifier ON or OFF.
R. POWER CORD SOCKET - Connect
the included power supply cord in
accordance with the voltage and
frequency ratings listed on the rear
panel.
w
w w
w w
w . . m
m r
r g
g e
and
Drive
channels
®
®
the
footswitch
overrides
e a
a r
r h
h e
e a
a d
d . . n
with
®
®
When
the
n e
e t
t

Publicidad

loading