Numark X5 Guia De Inicio Rapido página 5

7. EQ:
• Treble (Input Level High EQ): Adjusts the high (treble) frequencies of the corresponding
channel. Turning the knob completely to the right increases the level, turning the knob completely
to the left decreases the level to "off." This frequency "kill" control allows for unique mixing styles.
• Middle (Input Level Midrange EQ): Adjusts the mid-range frequencies of the corresponding
channel. Turning the knob completely to the right increases the level, turning the knob completely
to the left decreases the level to "off." This frequency "kill" control allows for unique mixing styles.
• Bass (Input Level Low EQ): Adjusts the low (bass) frequencies of the corresponding channel.
Turning the knob completely to the right increases the level, turning the knob completely to the
left decreases the level to "off." This frequency "kill" control allows for unique mixing styles.
8. LINE / PHONO / TRANS SWITCH (Input Selector Switch): These three-position toggles select what
input source is engaged among the connected units – and a flash position to allow rapid transforming
(audio signal "kill") effect.
9. CHANNEL FADER (VCA Fader): Adjusts the audio level on the corresponding channel.
Note: This fader is user replaceable if it should ever wear out. Simply remove the facepanel and then
remove the screws holding it in position. Replace the fader with a quality authorized replacement from
your local Numark retailer.
10. CHANNEL FADER CONTOUR: Adjusts the slope of the channel fader curve. Flip switch to the left for
a smooth fade or to the right for a sharp cut.
11. REVERSE BUTTON (Channel Fader Reverse Control): Activation of this switch can reverse the
fader direction.
CUEING / MONITOR CONTROLS
12. STEREO LEVEL INDICATOR – Monitors the audio level of the Program mix or Cue Channel,
depending on the position of the METER ASSIGN button.
13. METER ASSIGN BUTTON: Determines whether audio from the Program mix or the Cue channel is
sent to the stereo level indicator.
• When MASTER is indicated, this meter displays the stereo output levels of your mixed signal
(Program Mix).
• When CH1 – CH2 is indicated, the meter shows the pre-fader levels of channels 1 and 2 (Cue
channel). You can use the channel "Gain" and "EQ" controls to match the levels of input signals
while cueing.
14. CUE GAIN KNOB (Headphone Level): This rotary control adjusts the levels of the headphones
connected to the front panel input.
15. CUE TONE KNOB (Headphone Tone Control): This rotary knob adjusts the tone of the headphone
output. The knob can be raised and lowered to hide away by pressing it down.
16. CHANNEL CUE SLIDER: Channels 1 and 2 can be previewed using this mini-crossfader. Sliding this
to the left plays the left channel-1 and sliding to the right plays the right channel-2.
17. CUE / MASTER BUTTON: When lit, only the Program mix is heard. When off, only the Cue channel is
heard.
18. HEADPHONES: Connect your 1/4" headphones to this output for cueing and mix monitoring.
Headphone output controls are located on the top panel. The Volume should always be set at its
lowest setting while connecting and disconnecting headphones to prevent damage to headphones
and/or your hearing.
CROSSFADER CONTROLS
19. CROSSFADER (Digital VCA Crossfader): This slide fader blends audio between CH-1 and CH-2. Its
action can be modified with the "Mode," "Slope", and "Direction" controls.
digital VCA technology to accurately determine slider position. Both the VCA and Digital technologies
combined allow for some very powerful effects.
Note: This fader is user-replaceable if it should ever wear out. Simply remove the facepanel and then
remove the screws holding it in position. Replace the fader with a quality authorized replacement from
your local Numark retailer.
20. CROSSFADER CONTOUR: Adjusts the slope of the crossfader curve. Flip switch to the left for a
smooth fade (mixing) or to the right for a sharp cut (scratching).
21. CF REVERSE: Activation of this switch reverses the assignment of CH-1 and CH-2 on the crossfader.
OUTPUT CONTROLS
22. MASTER KNOB: Adjusts the Master output level.
23. BOOTH KNOB: Adjusts the Booth output level.
5
This digital mixer uses