Cleaning And Maintenance - cecotec BREEZECARE 3000 Manual De Instrucciones

Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 15
ENGLISH
Room with computer, experiment equipment: 45-60 % RH
Room with piano: 40-60 % RH
Museum, exhibition hall, and library: 40-50 % RH
Place the device on a flat surface.
Take out the top cover, fill the water tank and then put the top cover back.
Place the water tank on the main base.
Plug the device to a power supply. The display will light up and the device will beep. After 2
seconds, the display will turn off and the device will enter standby mode.
Press on/off, the device will start working under mist mode at level 2. The blue light indicator
will turn on. The control panel will display the current humidity and then will display Mist
mode level 2 after 15 seconds. One minute later, it will display current humidity and back to
Mist mode again repeatedly.
Press Max./Min. and choose between the 3 mist speed levels. The corresponding digit will be
displayed: 1-Low, 2-Medium, 3-High.
While current humidity is being displayed, press Max./Min. to check the current mist speed
level and press again to select a different speed level.
Timer
There are 12 timer settings: 1, 2, 3, 4, 5, 6, 7, 8, 9, 10,11, 12 hours.
Press the Timer symbol, the display will show the first timer option, "0". Press the same
symbol repeatedly to select the desired operating time.
After 5 seconds of setting the desired time, the timer indicator will stop flashing indicating
the settings have been successfully saved.
After 1 minute, the display will show current humidity.
Press the Timer symbol until "-- --" is displayed or hold down the Timer symbol for 2 seconds
to cancel the timer.
When the timer is set, the display will show the remaining operating time.
Humidity
When the LED display is showing current humidity, press the Humidity symbol.
The humidity level can be set from 30 % RH to 90 % RH.
Every time the symbol is pressed, it will be increased by 5 %.
When it reaches 90 %, press again and the display will show "Co". Do not operate the device
for 5 seconds to cancel the humidity setting function.
Once the desired humidity level is set, the light indicator will flash 5 times indicating the
settings have been saved. Then, the display will show the target humidity level every 1
minute.
Note: If the target humidity is higher than the current humidity, the humidification function
38
BREEZECARE 3000
will work.
When the set humidity is 16 % RH higher than current humidity, the device will operate at mist
level 3.
When the set humidity is 10 % RH ~ 15 % RH higher than current humidity, the device will
operate at mist level 2.
When the set humidity is 1 % RH ~ 9 % RH, the device will operate at level 1.
When the target humidity is lower than the current humidity, the device will enter standby
mode.
Note: The mist speed cannot be adjusted under constant humidity function.
During operation, hold down the humidity symbol for 2 seconds to switch to Sleep mode. The
blue light indicator and the display will turn off.
Press any symbol to turn the display on again.
Long press the Humidity symbol to exit Sleep mode.
Auto shut-off system
When the tank runs out of water, the device will automatically stop operating. The red light
indicator will turn on.
Refill the water tank, and the device will continue operating with the previous settings. If the
tank is not refilled, the device will turn off after 5 minutes.
Warnings:
Never run the humidifier when there is no water in water the tank and water basin.
Only pour aroma oil into the aroma cotton. Do not pour any liquid other than clean water into
the water tank or water base.

4. CLEANING AND MAINTENANCE

Use a soft, damp cloth to clean the surface of the device.
Do not use detergent, scouring pads, chemically treated cloths, gasoline, benzene, alcohol,
thinner, or other solvents, as these can scratch and damage the tank and cause water
leakage.
Do not immerse the product in water or any other liquid.
If scale is built up due to the use of hard water, it is recommended to:
Use cold boiled water or distilled water.
Clean the transducer, water tank and basin humidifier every week.
Change the water in water tank more often to keep it fresh.
Make sure to pour out water from the water tank and dry the water basin before you store it
unused for a long time.
ENGLISH
BREEZECARE 3000
39

Hide quick links:

Publicidad

Tabla de contenido
loading

Tabla de contenido