Petzl ALVEO VENT Guia De Inicio Rapido página 2

Instructions for use / Mode d'emploi
3. Test / test Attaching hearing protection / Fixation des protections antibruit
Attaching
Clippage
Removing
Déclippage
Mounting the headlamp / Fixation de la lampe frontale
VIZIR face shield / Visière VIZIR
PIXA 1: E78AHB
A15
PIXA 2: E78BHB
PIXA 3: E78CHB
Absorbent foam for ALVEO
Mousse absorbante pour ALVEO
A20200
Standard stickers for ALVEO
Autocollants standards pour ALVEO
A20100
Reflective stickers for ALVEO
Autocollants réfléchissants pour ALVEO
A20110
Accessories / Accessoires Spare parts / Pièces détachées
(EN) ENGLISH
Helmet for work at height, rescue,
climbing and mountaineering
Field of application
This helmet is designed for work at height,
rescue, climbing and mountaineering only.
The chinstrap has a strength of 50 daN
(requirement of the EN 12492 standard) to
help keep the helmet on the head in case
of a fall.
The ALVEO VENT helmet meets only the
impact and penetration requirements of the
EN 397 standard.
WARNING, this ventilated helmet has no
electrical insulation rating.
Do not use this helmet in activities for which
it is not designed.
Activities at height present a risk of
serious head injury. Wearing a helmet can
significantly reduce this risk, but cannot
entirely eliminate it.
In a major impact, the helmet deforms to
absorb the maximum amount of energy
possible, sometimes to the point of
destroying the helmet.
WARNING
Activities involving the use of this
equipment are inherently dangerous.
You are responsible for your own
actions and decisions.
Before using this product, you must:
- Read and understand all instructions
for use.
- Get specific training in its proper use.
- Become acquainted with its capabilities
and limitations.
- Understand and accept the risks involved.
Failure to heed any of these warnings
may result in severe injury or death.
significantly reduce its protective - Mounting the headlamp: use the headlamp
properties without leaving visible clips, or the front slot on the helmet.
signs of damage. Retire your
Precautions for use
helmet after a major impact.
Consult the details of the inspection
- Your helmet can be damaged from
procedure to be carried out for each item of
improper care. Do not sit on it, pack it too
PPE on the Web at www.petzl.com/ppe
tightly, drop it, allow it to contact sharp or
Contact Petzl if there is any doubt about the
Replacement foam for ALVEO pointed objects, etc.
condition of this product.
Do not expose your helmet to high
Mousse de rechange pour ALVEO
temperatures, for example by leaving it inside
Instructions for use
A20210 a vehicle in direct sunlight.
- Certain chemical products, especially
1. Preparation
solvents, can damage your helmet. Protect
Use only the smooth areas for stickers
your helmet from exposure to chemicals.
and other markings. Petzl stickers are
- This helmet has been tested for use at
approved. For any other stickers, verify their
temperatures between -30 °C and +50 °C.
Responsibility compatibility with Acrylonitrile Butadiene
Petzl general
Styrene. Stickers may contain materials that,
WARNING, specific training in the activities
with time, can alter the physical properties
defined in the field of application is essential
information
of the helmet.
before use.
This product must only be used by 2. Adjustments
Lifetime / When to retire your
competent and responsible persons, or
2a. Adjust the headband to maximum size
equipment
those placed under the direct and visual
using the adjustment wheels and place the
control of a competent and responsible
For Petzl's plastic and textile products, the
helmet on your head.
person. maximum lifetime is 10 years from the date
2b. Position the adjusters under the ears. To
Gaining an adequate apprenticeship in of manufacture. It is indefinite for metallic
adjust the chinstrap backwards or forwards,
appropriate techniques and methods of
products.
slide the webbing through the chinstrap
protection is your own responsibility.
ATTENTION: an exceptional event can lead
positioning buckles.
You personally assume all risks and you to retire a product after only one use,
2c. Use the adjustment wheels to increase or
responsibilities for all damage, injury or depending on the type and intensity of
decrease the size of the headband.
death which may occur during or following
usage and the environment of usage (harsh
2d. Fasten the chinstrap using the buckle.
incorrect use of our products in any manner
environments, marine environment, sharp
You must hear the buckle "click" to ensure
whatsoever. If you are not able, or not in a edges, extreme temperatures, chemical
proper fastening. Tighten the chinstrap, it
position to assume this responsibility or to products, etc.).
should be snug, but comfortable. A correctly
take this risk, do not use this equipment.
A product must be retired when:
adjusted chinstrap reduces the risk of the
- It is over 10 years old and made of plastic
helmet coming off accidentally. You must pull
Nomenclature of parts
or textiles.
on the chinstrap to verify that the buckle is
- It has been subjected to a major fall (or
(1) Shell, (2) Headband, (3) Headband properly fastened.
load).
adjustment wheels, (4) Chin strap To open the buckle, press the button on the
- It fails to pass inspection. You have any
positioning buckles, (5) Chin strap fastening
chinstrap fastening buckle.
doubt as to its reliability.
and adjustment buckle, (6) Ventilation 2e. Adjust the vertical position of the
- You do not know its full usage history.
holes, (7) Side slots for mounting hearing headband adjustment system on your nape
- When it becomes obsolete due to changes
protection, (8) Headlamp clips, (9) Front by sliding it up or down along the webbing.
in legislation, standards, technique or
headlamp mounting slot, (10) Face shield
ATTENTION, be sure there is no slack in the
incompatibility with other equipment, etc.
mounting hole, (11) Internal liner. webbing between the headband adjustment
Destroy retired equipment to prevent
Principal materials: Acrylonitrile Butadiene system and the shell of the helmet.
further use.
Styrene (ABS) shell, polyester straps.
3. Test
Product inspection
Inspection, points to
Verify that the helmet is well seated and
In addition to the inspection before each use,
centered on the head. A well-adjusted helmet
verify an in-depth inspection must be carried out
(minimal movement front to back or side to
side), provides better protection. by a competent inspector. The frequency of
Before each use, check the condition of the
the in-depth inspection must be governed
shell and the headband attachment system
Accessories
by applicable legislation, and the type and
(verify there are no cracks or deformation
the intensity of use. Petzl recommends an
on the outside or the inside...). Check the - Use the side slots to attach hearing
inspection at least once every 12 months.
condition of the webbing and stitching. protection. Use a screwdriver to remove
To help maintain product traceability, do not
Verify that the headband adjustment system them.
remove any markings or labels.
and chinstrap buckle are functioning - Mounting the face shield: use the face
Inspection results should be recorded on
shield mounting hole, or the side slots.
properly.
a form with the following details: type of
WARNING, a major impact to the helmet can
+ 50°C / + 122°F
- 30°C / - 22°F