Technical Specifications - BFT PHOBOS N Instrucciones De Instalación

2) GENERAL INFORMATION
Electromechanical operator designed to automate residential-type gates.
The gearmotor keeps the gate locked on closing and on opening, without
needing an electric lock for leaves up to 3 m long. For leaves ranging between
3m and 5m long, the electric lock becomes indispensable.
The operator is provided with an electronic torque limiter. It must be controlled
by an electronic control panel provided with torque setting.
The end-of-stroke operation is controlled by two magnetic limit devices.
The operator is provided with an obstacle detection system complying with
EN12453 and EN 12445 standards.

3) TECHNICAL SPECIFICATIONS

PHOBOS N - NL
Power supply
Absorbed power
Absorbed current
Insulation class
Thermal protection
Pushing and towing force
Speed
Impact reaction
Manual manoeuvre
Environmental conditions
Type of use
Maximum leaf length without
electric lock
Maximum leaf length with
electric lock
Maximum leaf weight
Degree of protection
Operator weight
Dimensions
Lubrification
(*) Available in all power supply voltages.
4) TUBE ARRANGEMENT Fig. A
Install the electrical system referring to the standards in force for electrical
systems CEI 64-8, IEC 364, harmonization document HD 384 and other
national standards.
Warning! For actuator wiring and accessory connection, refer to the relevant
instruction manuals. The control panels and accessories must be suitable for
use and conform to current standards.
Should the opening or closing direction be incorrect, it is possible to invert
the connections of operation 1 and operation 2 on the control board.
The first command after an interruption of the power supply should be an
opening manoeuvre.
5) INSTALLATION DIAGRAM Fig. B
P rear bracket fastening to pillar
F front fork fastening leaf
a-b distances for determining bracket "P" fastening point
C value of fastening centre-to-centre distance
D gate length
X distance from gate axis to corner of pillar
S half door thickness
Z value always greater than 45 mm (b - X)
kg max. weight of leaf
leaf opening angle
α°
6) PILLAR FASTENINGS INSTALLATION DISTANCES Fig. B Rif. 2 - 3
6.1) How to read the installation distance tables
Select "a" and "b" according to the angle in degrees α° that the gate has to
open. The optimum "a" and "b" values for 92° opening at constant speed are
highlighted.
If there is too large a difference between "a" and "b", the leaf will not travel
smoothly and the pushing or pulling force will fluctuate during its stroke.
To respect the opening speed and ensure the controller operates correctly,
10 -
PHOBOS N - PHOBOS NL
INSTALLATION MANUAL
single-phase 230V~ ±10% 50 Hz(*)
210 W
0,8 A
F
110 °C (self-resetting)
2000 N (~200 kg)
approx. 20 mm/s
Electronic clutch on control panel
CLS release key
from -20 °C to + 50 °C
semi-intensive
1,8 m Phobos N
3 m Phobos NL
5 m Phobos NL
2500 N (~250 kg)
IP X4
50N (~5kg) PHOBOS N
77N (~7,7kg) PHOBOS N L
See Fig. L
permanent grease
it is best to keep the difference between "a" and "b" as low as possible.
The table has been worked out for a 40 mm (PHOBOS NL), 20 mm (PHOBOS
N) thick medium-size gate. Always check that there is no possible collision
between the gate and the operator.
7) FASTENING OF FITTINGS TO PILLAR Fig. C
8) POWER CABLE Fig. D
The board power supply cable must be of the H 05 RN-F type or equivalent.
The equivalent cable must guarantee:
- permanent outside use
- maximum temperature on the cable surface of +50° C
- minimum temperature of -25° C
The wiring of the terminal board must be carried out as shown in Fig. D
Ref. 3:
MOT OP = operation 1
MOT CL
= operation 2
GND = earthing
MOT COM = common
Position the cable sheath so that O ring "K" is inserted in its housing in the
base and, leaving the sheath protrude by about J=5 mm (as shown in Fig. D
Ref. 3), close the hatch and fix it by means of the 3 screws.
9) ATTACHING MOTOR TO FASTENING ON PILLAR Fig. E
10) MAXIMUM TILT Fig. F
11) CORRECT INSTALLATION Fig. G
Correct installation entails maintaining a rod stroke margin of approx. 5-10
mm to avoid possible trouble with operation.
12) FASTENING OF FITTINGS TO LEAF Fig. H
IMPORTANT: the front bracket must be fitted with the bush collar protruding
UPWARDS (Fig. g Ref. 1).
13) OPERATOR ATTACHMENT ON DOOR Fig. I
14) ADJUSTMENT OF THE LIMITING DEVICES Fig. J
The correct adjustment of the limiting devices is obtained by setting the
working time on the control board correctly. Refer to the instructions of
the control board.
WARNING: If the time set on the control unit is insufficient, the leaves might
not complete their run.
Slightly increase the working time on the control unit.
15) DIMENSIONS Fig. L
16) TIPS FOR SPECIAL INSTALLATIONS Fig. M, N, O.
With the leaf fully open, create a recess to accommodate the operator.
Fig. M gives the minimum dimensions of the recess for the various PHOBOS
N - PHOBOS N L models.
If distance "b" is greater than the values given in the installation tables:
- create a recess in the pillar Fig. N
- move the leaf so that it is flush with the pillar Fig. O.
17) LEAF STOPS AT GROUND LEVEL
For the actuator to work properly, it is advisable to use stops "Fig. P Rif. 1" to
stop the leaves both when they are open and closed, as illustrated in Fig.
P. The leaf stops must prevent the actuator rod from reaching the end of
its travel.
18) MANUAL OPENING (See USER GUIDE -FIG.Y-).
19) ELECTRIC LOCK
WARNING: In the case of leaves longer than 3m, it is indispensable
to install a solenoid latch.
For electric lock connection, the optional board is required (refer to the
appropriate instruction).