Descargar Imprimir esta página
Eaton HaloHome FTS20CW Instrucciones
Eaton HaloHome FTS20CW Instrucciones

Eaton HaloHome FTS20CW Instrucciones

Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

HOME
FTS20CW
FTS20CB
ENGLISH
ITEMS REQUIRED
(Purchase separately)
• Phillips screwdriver
• Weatherproof silicone caulk
IMPORTANT SAFETY INSTRUCTIONS
When using product, basic precautions should always be followed, including the following:
• Heed all warnings, including below warnings AND those included on product.
• Save these instructions and warnings.
• For outdoor use only.
• cULus LISTED for wet location.
• Disassembling your fixture will void the warranty.
• Your fixture is prewired and preassembled for easy installation.
WARNING
• Read and follow these instructions.
• Risk of fire/electric shock. If not qualified, consult an electrician.
• Disconnect power at fuse or circuit breaker before installing or servicing.
CAUTION
• Connect fixture to a 120-277 volt, 50/60 Hz power source. Any other connection voids
the warranty.
• Fixture should be installed by persons with experience in household wiring or by a
qualified electrician. The electrical system, and the method of electrically connecting
the fixture to it, must be in accordance with the National Electrical Code and local
building codes.
• Fixture designed for wall or eave mount to a junction box only. Mount fixture to a
grounded, recessed-mounted standard junction box marked for use in wet locations.
Fixture can be mounted to an outdoor rated surface mount junction box or when used
with the included adaptar plate kit. See kit instructions for proper installation methods.
NOTE: This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
TM
Questions?/Des questions?/ ¿Preguntas? 1-800-334-6871 ConsumerProducts@eaton.com
PACKAGING CONTENTS/ CONTENU DE L'EMBALLAGE/CONTENIDO DEL PAQUETE
B. Mounting bracket
A. Light fixture
Appareil d'éclairage
Support de montage
Accesorio
Soporte de montaje
E. FLD-KIT-SFCGND
F. Support hook
Adapter Plate Kit
Crochet
Plaque adaptatrice trousse
Placa daptadora equipo
C. Gasket
D. (2) #6-32 x 3/4 in. and (2) #8-32 x 3/4 in. junction box screws
Joint
Junta
G. (2) #8-32 x 1-1/4 in. cover
mounting screws
(2) vis de protection nº 8
de 32 x 1-1/4 po
(2) Tornillos #8-32 x 1-1/4 pulg.
de montaje de la cubierta
- Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician
for help.
• This device contains transmitter module
FCC ID: ZAFZ1-AVI1010 (IC ID: 20544-AVI1010)
WARNING: FCC Regulations state that any
unauthorized changes or modifications to this
equipment not expressly approved by the manufacturer
could void the user's authorization to operate this
equipment. FCC Radiation Exposure Statement: The
equipment complies with FCC Radiation exposure limits
set forth for uncontrolled enviroment. This equipment
should be installed and operated with minimum
distance 20cm between the radiator and your body.
NOTE: This device complies with Industry Canada
license-exempt RSS standard(s). Operation is subject
to the following two conditions: (1) this device may not
cause interference, and (2) this device must accept any
interference including interference that may cause
undesired operation of the device.
SAVE THESE INSTRUCTIONS.
FOR BEST RESULTS
• Install light 8-16 feet above the ground.
• When installing two fixtures on one switch,
make sure the switch is rated for at least a
1 A inductive load.
MOUNTING AND WIRING YOUR FIXTURE
WARNING: Risk of electric shock. Disconnect
power at fuse or circuit breaker before installing
or servicing.
NOTE: Fixture can be wall or eave mounted (Fig. 1).
NOTE: Coverplate mounts to recessed mounted
standard junction boxes (Fig. 2). Junction box must be
at least 1-1/2 inch in depth for proper installation for
recessed mount application. For surface mount junction
box installation, refer to installation instructions included
with the adaptar plate kit (E).
1. Line up the holes on the mounting bracket (B) with
the holes on your junction box. Using either (2) #6
screws or (2) #8 screws (D) (depending on size of
the holes in your junction box), attach the mounting
bracket (B) to your junction box (Fig. 3).
2. Thread fixture wires through mounting bracket (B)
and gasket (C) (Fig. 6).
1
Instruction Manual/ Instrucciones
(use the size that fits your junction box)
(2) vis nº 6 de 32 x 3/4 po et 2 vis nº 8 de 32 x 3/4 po pou
boîtier de jonction (choisissez la dimension convenant
à votre boîtier de jonction)
(2) Tornillos #6-32 x 3/4 pulg. y (2) tornillos #8-32 x 3/4 pulg.
para montaje de la caja de conexión (utilice el tamaño
que mejor se adecue a su caja de conexión)
H. (2) Decorative screw cover caps
(2) cache-vis décoratifs
(2) Cubiertas tapatornillos decorativas
1
2
1-1/2 in.
Round
3
B
D
D
4
5
G
F
Wall mount
Eave mount
1-1/2 in.
Octagonal
Junction box
E
F
G
F
A

Publicidad

loading

Resumen de contenidos para Eaton HaloHome FTS20CW

  • Página 1 HOME Instruction Manual/ Instrucciones Questions?/Des questions?/ ¿Preguntas? 1-800-334-6871 ConsumerProducts@eaton.com PACKAGING CONTENTS/ CONTENU DE L’EMBALLAGE/CONTENIDO DEL PAQUETE B. Mounting bracket A. Light fixture C. Gasket D. (2) #6-32 x 3/4 in. and (2) #8-32 x 3/4 in. junction box screws (use the size that fits your junction box) Appareil d’éclairage...
  • Página 2: Troubleshooting

    REMARQUE : Cet équipement a été évalué et déclaré conforme aux limites des appareils Eaton warrants to customers that, for a period of five years from the date of purchase, Eaton numériques de classe B, conformément au point 15 du règlement de la FCC. Ces limites sont products will be free from defects in materials and workmanship.
  • Página 3: Garantie Limitée De 5 Ans

    PARTICULIER. Eaton garantit à ses clients, pendant une période de cinq ans à compter de la date d’achat, REMARQUE : L’appareil d’éclairage peut être monté sur le murale o sur l’avant toit (Fig. 1). que ses produits Eaton sont exempts de tout défaut de matériaux et de fabrication. En vertu REMARQUE : La plaque de couvercle s’installe aux boîtiers de jonction encastrés standards.
  • Página 4: Diagnostico Y Solucion De Problemas

    Esta garantía se extiende sólo para el comprador original del producto. Un recibo del comprador u otra prueba de la fecha de compra original aceptable para Eaton. Esto es necesario para la ejecución de la garantía. Esta garantía no se aplica a los productos de...
  • Página 5 La reproducción de este documento sin la aprobación previa por escrito de Eaton está estrictamente prohibida. Para solicitar ayuda, llame al 1-800-334-6871 o envíe un correo electrónico a ConsumerProducts@eaton.com...

Este manual también es adecuado para:

Halohome fts20cb