Troubleshooting - Connectivity - Whirlpool WDT975SAHZ Manual De Instrucciones

Follow Cycle Progress
Follow Cycle Progress lets you remotely monitor your dishwasher
and anticipate when it will finish the current cycle. Open the app
and select DISHWASHER. The cycle progress is displayed in
the app.
Select or Deselect Push Notifications
Push notifications let you choose which events will be announced
with a text message. Open the app and select DISHWASHER,
then open PREFERENCES. Turn on the push notifications you
want to receive.
Download a Specialty Cycle or My Cycle
The Download & Go™ feature lets you select a Specialty Cycle
or you can design a My Cycle on the Whirlpool
to your dishwasher. When the dishwasher receives the cycle, the
Download & Go LED lights up for several minutes to indicate the
cycle has been received. When you want to use this cycle, touch
DOWNLOAD & GO to select the cycle, just as you would do for
any other cycle. Press START/RESUME and close the door within
4 seconds to start the cycle.
HELPFUL TIP: The cycle will be remembered for future use until
a different cycle is downloaded to the dishwasher.
First try the solutions suggested here. If you need further assistance or more recommendations that may help you avoid a service
call, refer to the "Connectivity Setup" section in this manual or contact the Connected Appliance
In the U.S.A. Connected Appliance Team:
Visit www.whirlpool.com/connect
Call: 1-866-333-4591 M-F 8 am - 8 pm EST
Email: Connected_appliance@Whirlpool.com
By mail:
Connected Appliance Team
Whirlpool Customer eXperience Center
553 Benson Road
Benton Harbor, MI 49022-2692
Please include a daytime phone number in the correspondence.
4
app and send it
®
Troubleshooting – Connectivity
A
B
A. Wireless Status icon
B. Remote Enable icon
NOTE: If Download & Go is touched without a cycle ready for
selection, the LED will blink and you will hear an "invalid key
press" sound (if key activation sounds are turned on). When a
remote start command is received from the app, the dishwasher
will start the cycle. The Remote Enable icon will remain lit.
Enable Quiet Mode
Enable Quiet Mode lets you remotely silence the on-dishwasher
tones such as the end of cycle signal. Open the app and select
QUIET MODE.
Issue Alerts
Issue Alerts lets you know by text message if something needs
your attention and provides guidance about what to do. You
may turn off Issue Alerts from the app by going to the Appliance
Details page, choosing the Preferences option and toggle off all
notifications and click save in the top right corner.
Enable Kosher Consumer Friendly Mode
The Kosher Consumer Friendly mode lets you automatically
configure the dishwasher for observance of the Sabbath. Open
the app, select DISHWASHER, and then turn on SABBATH mode.
The dishwasher will continue to operate in Sabbath mode at the
appointed time every week until Sabbath mode is turned off.
Smart Delay
(Opt-in through Whirlpool
supported by your local utility)
During times of peak electrical rates (if you have opted in), you
may see the Smart Delay icon. When this occurs your dishwasher
will delay according to your opt-in choices to help alleviate peak
power demands on the local utility. The dishwasher will start up
automatically when the peak power demand has decreased. You
may override Smart Delay through the app.
In Canada contact the Connected Appliance Team:
Visit: www.whirlpool.ca/en_CA and click on the Whirlpool
Connected Appliances link
Call: 1-866-333-4591 M-F 8 am - 8 pm EST
Email: Connected_appliance@Whirlpool.com
By mail:
Connected Appliance Team
Whirlpool Customer eXperience Centre
200 – 6750 Century Ave.
Mississauga, Ontario L5N 0B7
C. Amber House icon (peak electric rates)
D. Blue House icon (normal electric rates)
u
app and when
®
Team.
C
D
q
®