Handling the equipment
ATTENTION!
It is not recommended to use or store the appa-
!
ratus in a damp room as this may cause it to rust. Please
ensure that no part of the machine comes in contact with liquids
(drinks, perspiration etc.). This may cause corrosion.
■ Before using the equipment for exercise, check carefully to
ensure that it has been correctly assembled.
■ The machine is designed for use by adults and children should
not be allowed to play with it. Children at play behave unpre-
dictably and dangerous situations may occur for which the manu-
facturer cannot be held liable. If, in spite of this, children are
allowed to use the equipment, ensure that they are instructed
in its proper use and supervised accordingly.
■ Before beginning your first training session, familiarize yourself
thoroughly with all the functions and settings of the unit.
■ A slight production of noise at the bearing of the centrifugal mass
is due to the construction and has no negative effect upon ope-
ration. Possibly occurring noise during reverse pedalling result
from engineering and are absolutely safe.
■ The exercise cycle has a magnetic brake system.
■ The equipment is independent of revolutions per minute.
■ Please ensure that liquids or perspiration never enter the machine
or the electronics.
■ Before use, always check all screws and plug-in connections as
well as respective safety devices fit correctly.
■ Always wear suitable shoes when using.
■ For a comfortable training position please adjust the hand-
lebar andsaddle position to your body height.
■ Nobody may be in the moving range of a training person
during training.
■ Calibration of the device can only be carried out by the manu
facturer. Note: a calibration diagram is included.
List of spare parts page 42-43
When ordering spare parts, always state the full article number,
spare-partnumber, the quantity required and the S/N of the product
(see handling).
Example order: Art.no. 07682-600/ spare-part no. 10100030 /
2 pieces / S/N ....................
Please keep original packaging of this article, so that it may be
used for transport at a later date, if necessary.
Goods may only be returned after prior arrangement and in
(internal) packaging, which is safe for transportation, in the original
box if possible.
It is important to provide a detailed defect description / damage
report!
Important: spare part prices do not include fastening material; if
fastening material (bolts, nuts, washers etc.) is required, this should
be clearly stated on the order by adding the words „with fastening
material".
Instructions for Assembly
RISK!
!
Ensure that your working area is free of possible sources
of danger, for example don't leave any tools lying around.
Always dispose packaging material in such a way that it may
not cause any danger. There is always a risk of suffocation if
children play with plastic bags!
■ Ensure that you have received all the parts required (see check
list) and that they are undamaged. Should you have any cause
for complaint, please contact your KETTLER dealer.
■ Before assembling the equipment, study the drawings carefully
and carry out the operations in the order shown by the diagrams.
The correct sequence is given in capital letters.
■ The equipment must be assembled with due care by an adult
person. If in doubt call upon the help of a second person, if pos-
sible technically talented.
■ Please note that there is always a danger of injury when working
with tools or doing manual work. Therefore please be careful
when assembling this machine.
■ The fastening material required for each assembly step is shown
in the diagram inset. Use the fastening material exactly as
instructed.
■ Bolt all the parts together loosely at first, and check that they
have been assembled correctly. Tighten the locknuts by hand
until resistance is felt, then use spanner to finally tighten nuts
completely against resistance (locking device). Then check that
all screw connections have been tightened firmly. Attention: once
locknuts have been unscrewed they no longer function cor-
rectly (the locking device is destroyed), and must be replaced.
■ For technical reasons, we reserve the right to carry out preliminary
assembly work (e.g. addition of tubing plugs).
Waste Disposal
KETTLER products are recyclable. At the end of its
useful life please dispose of this article correctly and
safely (local refuse sites).
GB
KETTLER GB Ltd.
Kettler House, Merse Road
North Moons Moat
Redditch, Worcestershire B98 9HL
+44 1527 591901
www.kettler.co.uk
KETTLER International Inc.
USA
1355 London Bridge Road
Virginia Beach, VA 23453
www.kettlerusa.com
+44 1527 62423
Mail: sales@kettler.co.uk
+1 888 253 8853
+1 888 222 9333
5