Installation Instructions - Mitel 5330 Guia De Inicio Rapido

Important Safety Instructions and Precautions
WARNING:DO NOT CONNECT DIRECTLY TO THE PUBLIC SWITCHED
TELEPHONE NETWORK (PSTN). ANY CONNECTION OF THIS UNIT TO
AN OFF-PREMISE APPLICATION, AN OUT-OF-PLANT APPLICATION,
ANY OTHER EXPOSED PLANT APPLICATION, OR TO ANY EQUIPMENT
OTHER THAN THE INTENDED APPLICATION MAY RESULT IN A SAFETY
HAZARD, AND/OR DEFECTIVE OPERATION, AND/OR EQUIPMENT
DAMAGE. AN "EXPOSED PLANT" IS WHERE ANY PORTION OF THE
CIRCUIT IS SUBJECT TO ACCIDENTAL CONTACT WITH ELECTRIC
LIGHTING OR POWER CONDUCTORS OPERATING AT A VOLTAGE
EXCEEDING 300V BETWEEN CONDUCTORS OR IS SUBJECT TO
LIGHTNING STRIKES.
WARNING:THE MITEL CORDLESS MODULE AND ACCESSORIES ARE
FOR USE ONLY WITH SPECIFIED MITEL EQUIPMENT.
WARNING:Users are not permitted to make changes or modify the device in
any way. Changes or modifications not expressly approved by Mitel
Corporation may void the user's right to operate the equipment.
When using your phone and cordless accessories, basic safety precautions
should always be followed to reduce the risk of fire, electric shock and injury to
persons, including the following:
• Do not use the product near water, for example, near a bath tub, wash
bowl, kitchen sink or laundry tub, in a wet basement or near a swimming
pool.
• Avoid exposing the product to rain or other liquids.
• Do not use the phone and cordless accessories to report a gas leak in the
vicinity of a leak.
Maintenance and Repair: There are no user serviceable parts inside these
units. For repairs, including battery replacement for the cordless handset,
return the unit to an authorized Mitel dealer. To replace the battery for the
cordless headset go to www.jabra.com, and refer to GN Netcom battery kit part
number 14151-02.
CAUTION: Installation of Modules shall only be performed by Mitel-qualified
personnel.
These notices may appear on the product or in the technical documentation.
Danger indicates an imminently hazardous situation which, if not
DANGER
avoided, will result in death or serious injury.
Warning indicates a potentially hazardous situation which, if not
WARNING
avoided, could result in death or serious injury.
Caution indicates a potentially hazardous situation which, if not
CAUTION
avoided, may result in minor or moderate injury and/or damage to the
equipment or property.
This symbol may appear on the product.
!
The exclamation point within an equilateral triangle indicates that important
operating and maintenance (servicing) instructions are included in the
literature accompanying the product.
Safety Instructions for the Cordless Handset
WARNING:THE CORDLESS HANDSET CONTAINS A BATTERY. CHARGE
ONLY WITH SPECIFIED CHARGERS ACCORDING TO
MANUFACTURER'S INSTRUCTIONS. DO NOT OPEN THE HANDSET,
DISPOSE OF IN FIRE, OR SHORT CIRCUIT – MAY IGNITE, EXPLODE,
LEAK, OR GET HOT CAUSING PERSONAL INJURY.
CAUTION:The battery in the Cordless Handset can explode, leak or catch fire
if exposed to high temperatures or fire, opened, or disassembled.
CAUTION:If fire or explosion occurs when the Cordless Handset is on charge,
shut off power to the IP phone, flood the area with water. LITH-X or copper
powder fire extinguishers, sand, dry ground dolomite or soda ash may also be
used.
2
Description
The Cordless Module connects to a 5330/5340/5360 IP Phone to enable
adding
• A Cordless Handset.
• A Cordless Headset and Headset Charging Cradle.
The 5330/5340/5360 IP Phones are LAN-powered. They supply power to the
Cordless Module and also provide power to charge both the cordless handset
and headset.
NOTE: The Cordless Module cannot be installed on a phone set that has a
Line Interface Module, IP PKM Module, or 5310 Conference Unit installed.
NOTE: For best performance, it is recommended that the cordless handset and
headset be used within your office or adjacent offices. (Maximum transmission
distances may vary depending on building construction.)
System Software Requirements
The Cordless Module and accessories are supported by the following system
software:
• 3300 IP Communications Platform (ICP) Release 9.0 UR1 and later
software
• 5000 Communications Platform (CP) Release 3.0 and later software
• SX-200 IP Communications Platform (ICP) Release 4.0 UR3 and later
software.
Supporting Documentation
For more information on the Cordless Module, Handset, and Headset, refer to
the appropriate system-specific technical documentation available at Mitel
Online. To access the 5330/5340/5360 IP Phone documentation:
1. In your browser, go to www.edocs.mitel.com.
2. Click End User Documents in the menu bar or under Other Resources
in the left side navigation pane.
Disclaimer
DUE TO THE DYNAMIC NATURE OF THE PRODUCT DESIGN, THE
INFORMATION CONTAINED IN THIS DOCUMENT IS SUBJECT TO
!
CHANGE WITHOUT NOTICE. MITEL NETWORKS CORPORATION, ITS
AFFILIATES, AND/ OR ITS SUBSIDIARIES ASSUME NO
RESPONSIBILITY FOR ERRORS AND/OR OMISSIONS CONTAINED IN
THIS INFORMATION.
ICP Programming
Before the 5330/5340/5360 IP Phone can be used, it must be registered with
the ICP. For information, refer to the Mitel 5330/5340 IP Phone Installation
Guide or the 5360 IP Phone Installation Guide available at Mitel OnLine. The
Cordless Module and accessories do not require registration with the ICP.

Installation Instructions

Attaching the Cordless Module to the 5330/5340/5360 IP
A
Phone (see Figure )

Disconnect the LAN power supply cable from the back of the phone.
CAUTION: Attempting to remove the backplate from the phone before discon-
necting the phone's power supply may damage the phone.

Remove the screw from the backplate on the back of the phone. Keep the
screw in a safe place—you must use the same screw in step

Place your thumb into the groove on the lower edge of the backplate above
the PC port, and firmly lift the backplate off. Insert the supplied jumper
connector into the 4-pin connector on the main board of the 5330/5340/
5360 phone.

Align the Cordless Module in vertical position against the phone and ensure
that the connector on the module aligns with the connector on the main
board of the 5330/5340/5360 phone.

Press forward and down firmly until the Cordless Module snaps into place.

.