Maintenance Tools - Ingersoll Rand Multi–Vane 2XJA1 Manual De Funcionamiento Y Mantenimiento

Parts used on Model 22N51–W/RC Base Mounted Motors are illustrated in the accompanying view and from the list below.
All others are the same as corresponding parts for Drills illustrated on page 20 and should be ordered accordingly.
Spindle Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
251 Spindle (All other parts included in the Spindle Assembly
are the same as those included in the Spindle Assembly of Drills.) . . . . . . . E22N–8
252 Motor Housing
* Warning Label
* Nameplate
253 Forward Inlet Stud . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
254 Forward Inlet Stud Lock Screw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TCCW–433
255 7/16" Lock Washer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D02–537
256 Reverse Inlet Stud . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . R22H–472
257 Reverse Inlet Stud Lock Screw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . T05–44
258 1/8" Pipe Plug . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . R2–227
259 Governor Valve Spring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . R22F61–431
259A Governor Valve Bushing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . R22F61–429
∅
Housing Long Stud (4) (All other parts included
in the Motor Housing are the same as those included
in the Motor Housing of Drills.) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . R22N51–133
⊗
Cylinder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
260 Backhead . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
261 1/8" Pipe Plug (All other parts included in the
Backhead are the same as those included in the Backhead for Drills)
(See illustrated part 12) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . R2–227
262 Motor Mounting Screw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
263 Rear Motor Mounting Bracket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
264 Front Motor Mounting Bracket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
265 Motor Mounting Base . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
266 Base Cap Screw (4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
267 Base Cap Screw Lock Washer (4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
269 Spindle Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
* Not illustrated.
∅ See illustration No. 3 for Drills. Order by Part Number shown above.
⊗ See illustration No. 32 for Drills. Order by Part Number shown above.
DESCRIPTION
Grease Gun
Throttle Body Puller
Reverse Valve Bushing Reamer
MAINTENANCE SECTION
for models ending in –EU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . R22N51–EU–RC40
for all other models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . R222N51–RC40
for models ending in –EU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
for all other models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
for models ending in –EU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
for all other models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

MAINTENANCE TOOLS

PART NUMBER FOR ORDERING
OPERATION
Lubrication.
Pulling the Throttle Body (84) from the
Motor Housing (1) on Series 22 Drills.
Reaming the Reverse Valve Bushing (7) after
pressing it into the Motor Housing (1) on Series 22
Drills.
26
R2XN51–A8
EU–99
WARNING–10–99
R2H–EU–99
R2H–99
R22H–471
R22H61–3
R22H–102
T15–278
R22N51–304
R22N51–303
R22N51–564A
D02–506
D02–321
R2XH51–768
TOOL NO.
P25–228
10203
22733