Installation Recommendations; Hollow Shaft - Nidec LEROY-SOMER MANUBLOC 3000 Serie Instalación

1 - INSTALLATION
RECOMMENDATIONS
Installation must be performed by qualified personnel. Allow
sufficient room around the geared motor for plugs (or vessel)
accessibility:
- 200 mm: G1/4'' plug for Mub 31 to 35
- 500 mm: G3/4'' dipstick for Mub 36 to 38
1/4 H min.
Gearbox:
For the installation of Manubloc 3000 gearbox, follow the
"Recommendations" chapter in the general manual.
If the gearbox is fitted with a MU universal mounting with a stiff
coupling by key, we recommend the application of a lithium
paste (molykote TP42 or equal) on the motor shaft.
Motor:
For connection of the complete drive system (with brake),
follow the instructions of corresponding maintenance delivered
with the goods in the parcel.
1.1 - Identification
The gearbox nameplate:
1 - gearbox model and size
2 - operating position
3 - fixing type (NU, BS, BDn or BT...)
- possible options
4 - exact reduction
5 - serial number
6 - lubricant
4 1
Mub 3232 B5 BT MI
793378201 / 001
N°
18,7
i
MIN EP ISO
1.2 - Torque point
Manubloc torque must be absorbed by an appropriate torque
arm (not supplied).
Too much play can produce dangerous shocks during reverse
operation or gear changes, flexible mountings are therefore
recommended: dampers in stressed rubber (Silentbloc type).
The flat end of the housing has cross tapping for this type of
mounting according to the outline diagram. The other parts are
not supplied by Nidec Leroy-Somer.
Installation - MANUBLOC 3000
4031 en - 2020.03 / j
INSTALLATION - DRIVE SYSTEMS - MANUBLOC 3000
5 2 3 4 1
Mub 3232 B5 BT MI
446487801 / 001 STD
N°
77,5 33,3
i
min
-1
VG 220 MIN EP ISO
6
Flexible mounting
(Silentbloc)
YB
ØOR
Dimensions (mm) Mub 3132 Mub 32 Mub 33 Mub 34 Mub 35 Mub 36 Mub 37 Mub 38
RE 15 16
YB 26 37
YC 19 23
ØOR 14 14
Ø internal 14 14
Flexible
mounting Ø external 40 40
(Silentbloc)
thickness 15 15

1.3 - Hollow shaft

1 - Check that the cylindrical shaft has been machined in
accordance with standard NF - E 22 - 175, with a slide fit: g6,
(the hub is: H7).
2 - Check that the key is standard and the shaft is the minimum
length tapped at the end.
3 - Before mounting, degrease all the parts, taking care not to
splash any solvent on the seals.
Use grease (PAO compound) to lubricate any parts in contact,
to avoid corrosion.
Fixing on a shouldered shaft:
O ring seal
Mounting
O ring seal
5 2 3 7
MOTEURS LEROY-SOMER
DYNABLOC
Mounting should be performed as described in the procedure
above, without jolting.
The Mub gearbox is mounted on the machine shaft using a
95,2
min
-1
VG 220
threaded rod, screwed into the shaft.
By screwing the nut down onto the washer, the shaft is smoothly
6
inserted into the cylindrical hub.
Dismantling
O ring seal
Use a spanner with a diameter corresponding to the shaft thread
and turn until the shaft comes out.
RE
18 25 25 30 36
37 55 44 70 65
23 32 42 90 110
14 22 24 33 26
14 22 22 33 33
40 60 60 80 80
15 30 30 30 30
Fixing on an untapped shaft:
O ring seal
42
75
166
33
35
100
40
11