Publicidad
Idiomas disponibles
Idiomas disponibles
INSTALLATION FIGURES
FIGURES D'INSTALLATION
11
8
5
FIGURAS DE LA INSTALACIÓN
10
1
Figure 7
Page 4
INSTALLATION INSTRUCTIONS - ENGLISH
1. Remove fixture components and parts pack. Check that all
parts are included. See page 2.
Warning: Safely dispose of packaging materials.
Assistance may be required to support fixture
during installation.
Turn off power at fuse or circuit breaker box!
NOTE:
NOT suitable for use with dimmer, motion sensors or
other remote devices.
This fixture is intended for ceiling or stem mount.
a. Installed to standard J-Box. See Fig 2.
b. Installed to surface ceiling using 1/2"side con-
duit. See Fig 5.
c. 3/4" Conduit Stem mount. See Fig 6.
9
2. Disassemble Fixture: Loosen the four Lens screws (2) See
Fig 1. Remove the Lens (1) and preserve for future use.
3. Unscrew the four Screws(3) attached to Housing (9) See
Fig 7. Disconnect the LED plate from S hook (6) attached to
Housing (9) preserve for future use.
7
NOTE: Do not remove Tether (7) attached to Housing (9).
Do not remove LED Clamp (5) or touch yellow portion of LED
"VOIDS WARRANTY"
4. Removed top Plug (10) in Housing(9) for mounting to
6
surface or J -box or stem mounting. Remove side Plug (10)
for 1/2" conduit.
5. Housing installation (9): Prepare the mounting surface by
drilling proper size hole or by knocking out the appropriate
knockouts. See Fig (1).
6. Mount Housing (9) thought 4 holes or to standard J-Box
4
through knockout slot.
Note: Use appropriate mounting hardware for your specifica-
tion application (not provided).
3
Helpful Hint: Use silicone caulking (not Included) Between
mounting surface and Junction box for Moisture seal.
7. Use wire nuts (8) to make wiring connection as outline in
STEP 8. Push wire connections into Housing(9). Hook the
LED Plate(4) to Tether (7) align LED Plate and tighten four
Screw (3) to secure LED Plate (4) to Housing(9). Replace
the Lens(1) on to Housing(9). Tighten Lens Screw (2) with
required tool. See fig(7)
2
8. WIRING AND FIXTURE OPERATION CAUTION:
NOTE: Make sure power is turned off!
Connect fixture to supply wires rated for at least 90°C
(194°F).
Connect the house supply ground wire (copper) to
fixture Ground Screw(12) by tighten to housing (9).See
Fig(4)
Note: if the house wiring does not include a grounding
wire. Consult a qualified electrician to ensure adequate
grounding methods.
Use wirenut (8) to connect the black fixture wire to
black supply wire the white fixture wire to the white
(neutral) house supply wire. See Fig(7)
STEP-BY-STEP GUIDE
For proper connection, place wire nut over
wires and twist clockwise until tight.
9. Turn on electricity at fuse or circuit breaker and
verify success of installation.
10. Apply suitable silicone caulk (not provided)
around the entire perimeter of the fixture housing
where it contacts the mounting surface for mois-
ture seal.
NOTE: NOT FOR THROUGH WIRE.
Trouble Shooting Guide
If this fixture fails to operate properly, use the guide
below to diagnose and correct the problem.
Verify that fixture is wired properly.
Verify that fixture is grounded correctly.
The line voltage at the fixture is correct.
If further assistance is required, contact:
Technical Support at:
(800) 748-5070.
This LED light provides low maintenance ser-
vice with no bulbs to change. Clean surfaces
with mild soap and water. Do not use abrasive
materials such as scouring pads or powders,
steel wool or abrasive paper.
Page 5
Publicidad
