Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Frame rail
Hitch Shown In Proper Position
Equipment Required: Tape, Utility Knife, Tape Measure &
Marking Pencil, Lubricant or Soapy water
Fastener Kit: 75742F
Wrenches: 10mm, 17mm, 11/16,
Small Phillips head Screwdriver,
Apperance panel
16.25
Tie down
hook cut-out
Area to be Trimmed
j
Qty. (4)
Hex Bolt M10X1.25X30 CL8.8
k
Qty. (4)
Conical Washers
l
Qty. (1)
3/8-16 U-Bolt
m
Flat Washer 3/8"
Qty. (2)
Remove the appearance panel on driver's side, remove 5-plastic rivets, 3-hex nuts, 2 Phillips head screws located in wheel well behind
1.
the driver's side rear tire. This panel needs to be trimmed and reinstalled on vehicle.
2.
Run the (item 1) into existing weld nuts to clear the threads.
3.
Reinstall appearance panel if trimmed.
4.
Lower exhaust by removing rubber isolators from muffler hangers. Remove the outside isolator first then the inside isolator. Spraying
a lubricant or soapy water on the metal hanger rod and the rubber isolator helps removal.
5.
Tape (item 7) flat washer to rearward weld nut location on both frame rails.
6.
Raise hitch into position.
7.
Install M10 fasteners as shown.
8.
Install the 3/8 U-Bolt through the vehicle tie down hook and through the tie down hook attachment of the receiver. Install flat washer,
lock washers and 3/8 hex nuts as shown above.
9.
Tighten all fasteners to the required torque specification.
10.
Raise exhaust back into position and re-install rubber isolators.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
©
2012,2015,2016 Cequent Performance Products, Inc. Printed in Mexico
Installation Instructions
Honda CR-V
Fascia
8.50
3.00
4.25
Tighten all 3/8-16 GR5 fasteners with torque wrench to 30 Lb.-Ft. (41 N*M)
Tighten all M10 CL8.8 fasteners with torque wrench to 38 Lb.-Ft. (52 N*M)
Sheet 1 of 3
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or
Hitch type
Weight Distributing
Weight Carrying
Ball Mount
Wiring Access Location: SUV3
Inside isolator
l
Exhaust shown lower
Note:
Fasteners typical both sides
n
Qty. (2)
Lock Washer
o
Qty. (2)
3/8 Hex Nut
p
Flat washer ½"
Qty. (2)
75742N
Part Numbers:
75742
87621
44675
Max Gross
Max Tongue
Trailer WT (LB)
Not For Use With Spring Bars
4500 (2043 Kg)
675 (306 Kg)
Existing weld nuts
Tie
typical
down
hook
m
n
o
k
j
4-12-16
Form: F205 Rev A 5-6-05
WT (LB)
Tape flat
washer to
frame rail
p
k
j
Rev. D
Publicidad
Manuales relacionados para Cequent Performance Products 75742
Resumen de contenidos para Cequent Performance Products 75742
- Página 1 This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. © 2012,2015,2016 Cequent Performance Products, Inc. Printed in Mexico Sheet 1 of 3 75742N 4-12-16 Rev.
- Página 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. © 2012,2015,2016 Cequent Performance Products, Imprimé au Mexique Feuille 2 de 3 75742N 4-12-16 Rev.
- Página 3 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York, V.E.S.C. Regulación V-5 y SAE J684. © 2012,2015,2016 Cequent Performance Products, Impreso en Mexico Hoja 3 de 3...