Service And Repair - Vollrath Onion King 500N Manual Del Operador

OPERATION
WARNING
Sharp Blade Hazard
Blades are sharp and can cause cuts. To avoid injury from
sharp blades, handle with caution.
Prior to first use, wash the equipment. See the Cleaning section in this
manual.
1. Check that the equipment is clean and the blades are in good
condition. Do not use this equipment if the blades are not in good
condition. Contact Vollrath to order a replacement blade assembly.
2. Check for proper blade alignment. Slowly set the pusher head onto
the blade assembly. They should slide together with no obstructions.
If there are obstructions, examine the pusher fingers. If they are
nicked or burred, smooth the rough edges with a small flat file. The
spaces between the fingers must be uniform. Straighten any bent
fingers.
3. Prepare the food to be processed. Food must be 3" (2.6 cm) or less
in diameter.
4. Lift the handle and place the food on the rear of the blade assembly.
5. Remove your hands from the blade assembly area.
6. Grasp the safety handle with your left hand.
7. With your right hand, lower the handle to slightly score the food
product.
8. Raise the handle and then use a strong, quick, downward thrust on
the handle to push the food product through the blade assembly.
9. Repeat this process until you have prepared enough food product
for your daily needs.
TROUBLESHOOTING
Problem
Food is not cut cleanly or is
damaged.

SERVICE AND REPAIR

Serviceable parts are available on Vollrath.com.
To avoid serious injury or damage, never attempt to repair the unit or
replace a damaged power cord yourself. Do not send units directly to
The Vollrath Company LLC. Please contact Vollrath Technical Services
for instructions.
When contacting Vollrath Technical Services, please be ready with the
item number, model number (if applicable), serial number, and proof of
purchase showing the date the unit was purchased.
www.vollrath.com
Might be Caused By
Improper food preparation.
Blade tension is not correct.
Blades are damaged.
The Vollrath Company, L.L.C.
1236 North 18th Street
Sheboygan, WI 53081-3201 U.S.A.
Main Tel: 800.624.2051 or 920.457.4851
Main Fax: 800.752.5620 or 920.459.6573
Customer Service: 800.628.0830
Canada Customer Service: 800.695.8560
CLEANING
WARNING
Sharp Blade Hazard
Blades are sharp and can cause cuts. To avoid injury from
sharp blades, handle with caution.
To maintain the appearance and increase service life, clean this
equipment daily.
NOTICE: Food acids, if left on the blades, will erode and dull the
cutting edge prematurely. Always clean this equipment
immediately after every use.
NOTICE: Do not put this equipment in a dishwasher.
NOTICE: Hand wash using a solution of mild detergent and warm
water. Do NOT use harsh chemicals or scratching
cleansers. These can damage the equipment.
NOTICE: Do not wipe across the blades or use scrub pads on this
equipment. Wiping across the sharp edge of the blade can
cause injury and will dull the blades.
1. Raise the handle open to the highest position possible.
2. The blade assembly is best cleaned by using the cleaning brush
accessory (sold separately) to push food particles out from the
unsharpened side of the blade assembly.
3. If you do not have the cleaning brush, use water under pressure to
push food particles out from the unsharpened side of the blade
assembly.
4. Wipe, rinse or spray off equipment, pusher head assembly and blade
assembly thoroughly with HOT water.
5. Allow the equipment to air dry.
6. Lubricate the pivot rod with mineral oil or Petro-Gel after each use.
Do not use cooking oil as it will become sticky and may permanently
damage the equipment.
Course of Action
Pre-score food to avoid undue shock and stress to blades.
Use a torque wrench to tighten the screws that secure the blade assembly
to the base. Tighten to 70 in. lbs.
Replace the blade assembly.
WARRANTY STATEMENT FOR THE VOLLRATH CO.
This warranty does not apply to products purchased for personal,
family or household use, and The Vollrath Company LLC does not offer
a written warranty to purchasers for such uses.
The Vollrath Company LLC warrants the products it manufactures or
distributes against defects in materials and workmanship as specifically
described in our full warranty statement. In all cases, the warranty runs
from the date of the end user's original purchase date found on the
receipt. Any damages from improper use, abuse, modification or
damage resulting from improper packaging during return shipment for
warranty repair will not be covered under warranty.
For complete warranty information, product registration and new
product announcement, visit www.vollrath.com.
Technical Services
techservicereps@vollrathco.com
Induction Products: 800.825.6036
Countertop Warming Products: 800.354.1970
All Other Products: 800.628.0832
©
2017 The Vollrath Company L.L.C. Part No. 2350028-1 ml 2/6/17