Enders COSYSTAND Instrucciones De Instalación Y Servicio página 5

Assembly and usage instructions
Please store these instructions in a safe place for future reference.
Please read the usage instructions carefully before using your heater and observe the safety instructions.
Materials and manufacture have been carefully selected such that, if used properly, malfunction is not possible.
As a result of transportation it is possible in ex-ceptional cases that the radius of the partition may change slightly with the result that greater
force will be required when inserting in the gas canister housing. In this case, the partition can be adjusted/bent without danger by pulling
apart lightly or pressing together. This is sufficient to ensure easy insertion in the gas canister hous-ing again.
I. Montage
Before assembling your heater, please check the contents for
Completeness. (Fig. 1)
Item 1 Reflector
Item 2 Burner cpl
Item 3 Column
Item 4 Container lid
Item 5 Bulkhead
Item 6 Base
Item 7 Container housing
Item 8 Screw M8x20
Item 9 Screw M5x12
Item 10 Screw M6x12
Item 11 Hexagon nut M5
Item 12 Serrated washer Ø6,4
Item 13 Serrated lwasher Ø5,3
Item 14 Hexagon nut M8
Item 15 Edge protection, lenght 360 mm
Item 16 Edge protection, lenght 245 mm
Item 17 Adaptor
Item 18 Hexagon nut M6
Item 19 Clamp
1 Remove the protective foil from any panels!
2. Apply the edge protection (15,16) to the handle opening in the container housing (7/1+2) and bulkhead (5).
3. Join the two halves (7/1 and 7/2) of the container jacket together using the 4 screws (9), 4 serrated lock washers (13) and 4 hexagon
nuts (11) (Detail fig. F). Pay attention that the two halves are correctly aligned and connected. The left jacket half is marked with an „L"
punched in the upper edge. The resulting container jacket can now be screwed onto the base (6) using the 4 screws (9) and the corres-
ponding serrated lock washers (13) and hexagon nuts (11). (Detail fig. A)
4. Place the column (3) with disc downwards in the centre of the container (7), push the container lid (4) over the column and place onto the
container housing (7). Screw together the container lid (4) and container housing (7) with 4 screws (9), the appropriate serrated washers
(13) and hexnuts (11). (Detail fig. B)
5. Use the plastic adaptor supplied to fasten the central tube (3) in place. Place the adaptor (Detail C) on the top end of the central tube and
fix in place with 3 screws (10).
6. Place the burner (2) with the gas hose onto the column (3) and screw tight with 3 screws (10). (Detail fig. C)
7. Pull the column (3) upwards onto the container lid (4) as far as it will go and fasten to the container lid with 3 screws (8) and 3 hexnuts
(14). (Detail fig. D)
8. Screw the reflector (1) to the burner (2) using 3 hexagon nuts (18) and 3 serrated washers (12). (Detail fig. E)
9. Attach bulkhead (5).
10. Connect to the gas cylinder (see section II).
Detail fig. A
13
9
3
8
14
Detail fig. D
609992107_5305_Classic_Europe_261108.indd 5
1
1
1
1
1
1
1
3
12
6
12
3
12
3
1
3
1
3
1
Detail fig. B
9 13
11
11
8
4
GB
You will need the following
tools for assembly:
2 crosshead screwdrivers
1 spanners SW 8, SW 13, SW 17
piece
piece
piece
piece
piece
12
piece
8
13
piece
pieces
14
pieces
9
pieces
15
pieces
pieces
16
pieces
10
pieces
piece
11
17
pieces
piece
pieces
piece
Detail fig. C
2
10 10
17
10
3
18
12
Detail fig. E
5
E
18
360 mm
B
16
245 mm
7/1+2
A
Fig. 1
Detail fig. F
7/1 7/2
9 13
11
Expand your life
1
2
C
3
D
4
15
5
16
6
26.11.2008 13:58:53