Reggiani uniSio Manual Del Usuario página 8

The UNISIO range is divided into RECESSED and SURFACE MOUNTED luminaires.
The RECESSED line, consists of ready-to-mount luminaires requiring just drilling of holes. The
holes required for the various versions are as follows: 100 mm dia., 130 mm dia. and 195 mm
dia., as shown on the product label
Sometimes the luminaires are subdivided into two categories, luminaires with bezel or trimless
versions.
RECESSED TRIMLESS LUMINAIRES
The lamp bezel provided (fig.1) can be used to install the luminaires in false ceilings 12.5 mm
thick . After inserting the bezel into the recess
After mounting the bezel, finish the recess with plaster and smooth perfectly around the hole
RECESSED LUMINAIRES WITH 100 mm dia. BEZEL
To mount (fig.2), bend the supporting springs slightly
rotate a quarter of a turn in the direction of the arrow
RECESSED LUMINAIRES WITH 130 mm and 195 mm dia. BEZEL
To assemble/disassemble the bezel (fig.3), turn the spring clip upwards with the help of a screw-
driver or similar inserted between the spring and the pin
press on the spring with the fingers until it no longer clicks
After mounting the bezel, wire up (fig.4) (see general notes). IMPORTANT : To wire Class II
naires, use double insulated wires. Alternatively, protect the wires with the sheath provided and fix
it with cable collars
the connector in the socket. After wiring to the mains electricity supply, insert the luminaire into
the bezel, pressing lightly (fig.5). When you hear the characteristic "clack", the supporting spring
and bezel are fixed together.
THE SURFACE MOUNTED range is subdivided into pendants, track or surface mounted
luminaires
SURFACE MOUNTED LUMINAIRES AND PENDANTS
To fasten the base of the luminaire to the mounting surface follow the instructions given in the
figure (fig.6): loosen the safety screws;
springs; use the base as drilling template and fasten it with two suitable screws or expansion
plugs; connect to the mains (see General Notes)
luminaires requires the use of conductors with double insulation; alternatively the cable can be
protected with the sheath provided in the standard kit and fasten it with cable collars (see fig.4
). After the electrical connection, re-attach the body to the base
screws .
TRACK MOUNTED LUMINAIRES
The TRISIO track-mounted range consists of luminaires ready for mounting on the Reggiani 3-cir-
cuit electrified tracks (fig.9). For installation, follow the instructions given in fig.7. Loosen the
safety screws (fig.6
the safety screws of the cams
power supply cable to the adapter in the groove of the track
; tighten the safety screw
screws (fig.6 ); lastly fit the adapter (fig.9)
For fastening the luminaire to other types of electrified tracks (contact the Reggiani Engineering
Department to check compatibility), proceed to (fig.8): remove the mounting cam from the lumi-
naire ; unscrew the metal lug from locking cam
back on cam . Lastly follow the instructions given in the (fig.7).
To engage the adapter on the Reggiani electrified track (fig.9): observe the correct direction when
inserting adapter ; turn locking lever
chosen .
To fit the adapter to the ultra low profile 1-circuit track (fig.10): observe the correct engagement
direction (the logo should be facing towards the outside)
release the adapter, raise the anti-rotation device, then turn the adapter by 90°in the direction
opposite to that of engagement
ce fastened to it either on or off
UNISIO
PREPARATION AND ASSEMBLY OF THE LUMINAIRES
Turn the electricity off at the mains
and follow the instructions given below.
. After connecting, cover the terminals with the cable gland
); using a tool, press and release the retaining springs (fig.6
; fit the luminaire on the track being careful to accompany the
; re-attach the body to the base (fig.6
. The switch alongside the adapter serves for switching the devi-
.
.
, fix in place using the screws provided.
, insert the bezel into the recess and
to ensure it grips perfectly
using a tool, press and release the retaining
; CAUTION : electrical connection of Class IIa
. Turn the cam by 180°C
; select phase 1-2-3, according to the power supply line
; then turn the adapter by 90°
6
, fit the bezel into the hole
.
; lastly tighten the safety
; turn the cam by 90° using a tool
); tighten the safety
; screw the lug
ENGLISH
.
, and
a
lumi-
, then plug
); loosen
. To