Reggiani uniSio Manual Del Usuario página 9

MOUNTING THE REFLECTOR
Depending on the light source chosen, 130 mm and 195 mm dia. luminaires may be fitted
with a reflector. In particular:
art. 11300 = narrow beam reflector
PTL 20W 35W
G8,5 2X7° 2X7°
GY6,35
art. 11301 = medium beam reflector
PTL 20W 35W
G8,5 2x17° 2X17°
GY6,35
art. 11302 = wide beam reflector
PTL 20W 35W
G8,5 2X28° 2X28°
GY6,35
Low voltage halogen lamp HR-GS/UB GU5,3 50W max, (fig.11)
Pull the lamp to disengage it from the retaining springs;
Replace/fit the lamp with max. power rating as specified on the label;
push the lamp into the seat until engaged.
Mains voltage halogen lamps HR-GS/UB GZ10 50Wmax, Metal halide lamps BRITE-
SPOT GX10(35W) (only for self-protected lamps) (fig.12)
turn the lamp anti-clockwise to disengage it from the lamp holder;
replace/fit the lamp with max. power rating as specified on the label;
insert the lamp in the lamp holder and turn it clockwise to engage it
Low voltage halogen lamps HM-GS/UB G53 75Wmax (only for self-protected lamps)
(fig.13);
Pull the lamp to disengage it from the retaining springs;
Remove the Faston terminals and replace/fit the lamp with max. power rating as speci-
fied on the label;
Engage the Faston terminals on the lamp pins, being careful to kept the shielding part
facing outwards.
Attach the lamp to the springs
Metal halide lamp MT/UB G8,5 35/70W; G12 35/70/150W; Low voltage halogen lamp
HS-G/UB GY 6,35 50Wmax; Mains voltage lamp HR-G/UB G9 75W max (fig.16)
Before proceeding to insert/change the lamp, it is advisable to secure the reflector by
using the special spring clip supplied in the kit (fig.15)
ghtly as shown in the figure, in order to reduce its diameter and make it easier to insert
in bayonet cap
Remove the protective reflector by turning it anti-clockwise;
Insert/replace the lamp with one of equal rating as the ballast, see rating plate);
Re-engage the reflector correctly by turning it clockwise;
N.B. Always check the safety glass for intactness and for perfect fitting on the bayonet cap.
If it is necessary to replace the safety glass shields, always use original spare parts
UNISIO
50W 70W 150W
2X8°
2X9° 2X6°
50W 70W 150W
2X17°
2X12° 2x17°
50W 70W 150W
2X29°
2X15° 2X20°
INSTALLATION/REPLACEMENT OF LAMPS
Disconnect from the mains and following the instructions given below
. When the spring is seated, it appears as shown in figure
art. 11310 = narrow beam reflector
PTL 35W 50W
G12 2x5°
GX12 2x9°
art. 11311 = medium beam reflector
PTL 35W 50W
G12 2x16°
GX12 2x15°
art. 11312 = wide beam reflector
PTL 35W 50W
G12 2x20°
GX12 2x19°
7
70W 100W
2x5°
2x6°
70W 100W
2x16°
2x13°
70W 100W
2x21°
2x16°
. Press the spring clip sli-
.
ENGLISH
150W
2x8°
150W
2x16°
150W
2x23°