Noise/Vibration Information; Declaration Of Conformity - Bosch PMF 180 E Multi Manual Original

OBJ_BUCH-345-007.book Page 12 Wednesday, April 20, 2011 8:07 AM
12 | English

Noise/Vibration Information

Measured sound values determined according to EN 60745.
Typically the A-weighted noise levels of the product are:
Sound pressure level 85 dB(A); Sound power level 96 dB(A).
Uncertainty K <1.5 dB.
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 60745:
2
Sanding: a =6.4 m/s , K<2.0 m/s
h
Cutting with plunge cut saw blade: a
Cutting with segmential saw blade: a
2
K<1.5 m/s
2
Scraping: a =11.4 m/s , K=2.2 m/s
h
The vibration emission level given in this information sheet
has been measured in accordance with a standardised test
given in EN 60745 and may be used to compare one tool with
another. It may be used for a preliminary assessment of expo-
sure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or poorly maintained,
the vibration emission may differ. This may significantly in-
crease the exposure level over the total working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
Assembly
Changing the Tool
Before any work on the machine itself, pull the mains
plug.
Selecting the Application Tool/Accessory
The following table shows examples for application tools. Further application tools can be found in the extensive Bosch acces-
sories program.
Accessory
BIM segment saw
blade
Base plate for sand-
ing, series Delta
93 mm
HCS plunge cut saw
blade, wood
HCS plunge cut saw
blades, wood
2 609 004 835 | (20.4.11)
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working pe-
riod.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work pat-
terns.

Declaration of Conformity

2
We declare under our sole responsibility that the product de-
2 2
=9.9 m/s , K<1.5 m/s
scribed under "Technical Data" is in conformity with the fol-
h
2
=5.0 m/s ,
lowing standards or standardization documents: EN 60745
h
according to the provisions of the directives 2004/108/EC,
2
.
2006/42/EC.
Technical file at:
Robert Bosch GmbH, PT/ESC,
D-70745 Leinfelden-Echterdingen
Dr. Egbert Schneider
Senior Vice President
Engineering
Robert Bosch GmbH, Power Tools Division
D-70745 Leinfelden-Echterdingen
Leinfelden, 18.03.2010
Wear protective gloves when changing application
tools/accessories. Contact with the application tool/
accessoriy can lead to injuries.
Material Application
Wooden materials, plas- Separating and plunge cuts; also for sawing close to edges,
tic, non-ferrous metals in corners and hard to reach areas;
example: shortening already installed bottom rails or door
hinges, plunge cuts for adjusting floor panels
Depends on sanding sheet Sanding surfaces close to edges, in corners or hard to reach
areas;
depending on the sanding sheet for, e.g., sanding wood,
paint, varnish, stone
Wooden materials, soft Separating and deep plunge cuts; also for sawing close to
plastics edges, in corners and hard to reach areas;
example: narrow plunge cut in solid wood for installing a
ventilation grid
Wooden materials, soft Smaller separating and plunge cuts;
plastics example: cut-outs in furniture for cable connections
Dr. Eckerhard Strötgen
Head of Product
Certification
Bosch Power Tools