Noise/Vibration Information; Kickback Stop - Bosch Professional GWX 18V-15 C Manual Original

28 | English
Angle grinder
F)
Max. signal range
A) Rated no-load speed for the selection of appropriate application tools in accordance with EN IEC 62841-2-3. The actual no-load speed is
lower for safety reasons and according to production tolerances.
B) Measured at 20–25 °C with rechargeable battery ProCORE18V 8.0Ah and depending on the battery's state of charge as well as the tool's
operating temperature
C) Depends on rechargeable battery (7), protective guard ((17), (15), (18)) and auxiliary handle ((11), (12)) in use
D) Limited performance at temperatures < 0 °C
E) The mobile terminal devices must be compatible with Bluetooth® Low Energy devices (version 4.2) and support the Generic Access Profile
(GAP).
F) The signal range may vary greatly depending on external conditions, including the receiving device used. The Bluetooth® range may be signi-
ficantly weaker inside closed rooms and through metallic barriers (e.g. walls, shelving units, cases, etc.).

Noise/Vibration Information

Noise emission values determined according to EN IEC 62841-2-3.
Typically, the A-weighted noise level of the power tool is
Sound pressure level
Sound power level
Uncertainty K
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K determined according to EN IEC 62841-2-3:
h
Grinding surfaces (roughing) and abrasive cutting:
a
h
K
A)
Disc sanding:
a
h
K
A) determined with medium-hard backing pad
Grinding thin metal sheets or other materials that tend to easily vibrate with a large surface area can cause the noise emission value to increase by
up to 15 dB. Suitable, heavy damping mats can reduce the increased noise emissions. Increased noise emissions must be taken into considera-
tion, both for the risk assessment of the noise output and for selecting suitable hearing protection.
The vibration level and noise emission value given in these
instructions have been measured in accordance with a
standardised measuring procedure and may be used to com-
pare power tools. They may also be used for a preliminary
estimation of vibration and noise emissions.
The stated vibration level and noise emission value repres-
ent the main applications of the power tool. However, if the
power tool is used for other applications, with different ap-
plication tools or is poorly maintained, the vibration level
and noise emission value may differ. This may significantly
increase the vibration and noise emissions over the total
working period.
To estimate vibration and noise emissions accurately, the
times when the tool is switched off or when it is running but
not actually being used should also be taken into account.
This may significantly reduce vibration and noise emissions
over the total working period.
1 609 92A 6WT | (24.06.2022)
GWX 18V-15 C GWX 18V-15 SC
m 30
GWX 18V-15 C GWX 18V-15
3 601 JH6 4.. 3 601 JH6 5..
dB(A) 93
dB(A) 101
dB
3
2
m/s 6.0
2
m/s 1.5
2
m/s 2.5
2
m/s 1.5
Implement additional safety measures to protect the oper-
ator from the effects of vibration, such as servicing the
power tool and application tools, keeping their hands warm,
and organising workflows correctly.

Kickback stop

ated, the status indicator (35) flashes red.
To restart the tool, set the on/off switch (5) / (9) to the "off"
position and then switch the power tool on again.
GWX 18V-15 P GWX 18V-15 PSC
30 30
GWX 18V-15 P GWX 18V-15
SC
3 601 JH6 F.. 3 601 JH6 G..
93 89
101 97
3 3
6.0 4.8
1.5 1.5
2.5 < 2.5
1.5 1.5
If there is a sudden kickback in the power tool,
e.g. jamming in a separating cut, the power
supply to the motor will be interrupted elec-
tronically. The kickback stop indicator(31)
then lights up. When kickback stop is activ-
Bosch Power Tools
30
PSC
89
97
3
4.8
1.5
< 2.5
1.5