Optional Accessories - Makita GD0800C Manual De Instrucciones

GD0800C
–1
Number min (RPM)
1 – 2 7,000 – 10,000
2 – 3 10,000 – 17,000
3 – 4 17,000 – 24,000
4 – 5 24,000 – 28,000
006478
CAUTION:
• If the tool is operated continuously at low speeds for a
long time, the motor will get overloaded, resulting in
tool malfunction.
• The speed adjusting dial can be turned only as far as 5
and back to 1. Do not force it past 5 or 1, or the speed
adjusting function may no longer work.
ASSEMBLY
CAUTION:
• Always be sure that the tool is switched off and
unplugged before carrying out any work on the tool.
Installing the side handle (optional accessory)
(Fig. 3)
Install the side handle on the tool barrel, then tighten the
handle by turning clockwise at the desired position.
Installing or removing wheel point (Fig. 4 & 5)
Loosen the collet nut and insert the wheel point into the
collet nut. Use the smaller wrench to hold the spindle and
the larger one to tighten the collet nut securely.
The wheel point should not be mounted more than 8mm
from the collet nut. Exceeding this distance could cause
vibration or a broken shaft.
To remove the wheel point, follow the installation proce-
dure in reverse.
CAUTION:
• Use the correct size collet cone for the wheel point
which you intend to use.
OPERATION
(Fig. 6)
Turn the tool on without the wheel point making any con-
tact with the workpiece and wait until the wheel point
attains full speed. Then apply the wheel point to the
workpiece gently. To obtain a good finish, move the tool
in the leftward direction slowly.
CAUTION:
• Apply light pressure on the tool. Excessive pressure on
the tool will only cause a poor finish and overloading of
the motor.
MAINTENANCE
GD0810C
CAUTION:
–1
min (RPM)
• Always be sure that the tool is switched off and
1,800 – 2,400
• Never use gasoline, benzine, thinner, alcohol or the
2,400 – 4,100
4,100 – 5,800
To maintain product SAFETY and RELIABILITY, repairs,
5,800 – 7,000 carbon brush inspection and replacement, any other
maintenance or adjustment should be performed by
Makita Authorized Service Centers, always using Makita
replacement parts.

OPTIONAL ACCESSORIES

CAUTION:
• These accessories or attachments are recommended
If you need any assistance for more details regarding
these accessories, ask your local Makita service center.
• Wheel points
• Collet cone set (3 mm, 6 mm, 1/4", 1/8")
• Vise holder
• Wrench 13
• Wrench 19
• Side handle set
NOTE:
• Some items in the list may be included in the tool pack-
Noise
The typical A-weighted noise level determined according
to EN60745:
The noise level under working may exceed 80 dB (A).
The noise level under working may exceed 80 dB (A).
Vibration
The vibration total value (tri-axial vector sum) determined
according to EN60745:
If the tool is used for other applications, the vibration val-
ues may be different.
unplugged before attempting to perform inspection or
maintenance.
like. Discoloration, deformation or cracks may result.
for use with your Makita tool specified in this manual.
The use of any other accessories or attachments might
present a risk of injury to persons. Only use accessory
or attachment for its stated purpose.
age as standard accessories. They may differ from
country to country.
Model GD0800C
Sound pressure level (L
Uncertainty (K): 3 dB (A)
Model GD0810C
Sound pressure level (L
Uncertainty (K): 3 dB (A)
Wear ear protection
Model GD0800C
Work mode: surface grinding
Vibration emission (a
Uncertainty (K): 1.5 m/s
Model GD0810C
Work mode: surface grinding
Vibration emission (a
Uncertainty (K): 1.5 m/s
ENG905-1
): 78 dB (A)
pA
): 79 dB (A)
pA
ENG900-1
2
): 2.5 m/s
h, AG
2
2
): 2.5 m/s or less
h, SG
2
5