Introductory Comment; General Rules Of Safety; Symbology - ADIATEK 11 2011 Manual De Uso Y Mantenimiento

GB

INTRODUCTORY COMMENT

Thank you for having chosen our machine. This floor
cleaning machine is used for the commercial clean-
ing and is able to clean most types of hard floor, ex-
cept carpet cleaning (if unsure please consult your
floor manufacturer/supplier). During its forward
movement, the combined action of the brush and
the detergent solution removes the dirt which is re-
covered through the rear suction assembly, giving a
perfectly dry surface.
The machine must be used only for such purpose. It
gives the best performance if it is used correctly and
maintained in good condition. We therefore ask you
to read this instruction booklet carefully whenever
difficulties arise in the course of the machine's use.
In case of need, we ask you to contact our service
department for all advice and servicing as may prove
necessary.

GENERAL RULES OF SAFETY

The rules below have to be followed carefully in or-
der to avoid injury to the operator and damage to
the machine.
- Read the labels carefully on the machine. Do not
cover them for any reason and replace them imme-
diately if damaged.
- The machine must be used exclusively by author-
ized staff that have been instructed on its correct
and proper use.
- During the operation of the machine, pay attention
to other people and especially to the children.
- In the presence of children guard the machine, so
that they do not play with it.
- Do not touch or pass over the mains cable while
the brush is operating.
- The socket for the power supply must be equipped
with a standard earthing (ground) system.
- Do not damage the mains cable by squashings,
bendings or stressings.
- Check the integrity of the mains cable. If during
working a damage is noticed, stop the machine im-
mediately and replace the cable.
- Do not mix different detergents, avoiding harmful
odours.
- Storage temperature: between 0°C and +55°C.
- Perfect operating temperature: between 0°C and
40°C.
- The humidity should not exceed 95%.
- Do not use the machine in explosive atmosphere.
- Do not use the machine as a means of transport.
- Do not go up or down the stairs.
- Do not use acid solutions which could damage the
machine and/or the persons.
- Avoid brush operation when the machine is stand-
ing still in order to prevent floor damages.
- Do not use the machine on surfaces covered with
inflammable liquids or dusts (for example hydrocar-
bons, ashes or soot).
- In case of fire, use a powder based fire-
extinguisher. Do not use water.
- Do not strike shelvings or scaffoldings where there
is danger of falling objects.
- Do not use the machine on areas having a higher
gradient than the one stated on the number plate.
- The machine has to carry out simultaneously the
operations of washing and drying. Different opera-
tions must be carried out in restricted areas prohib-
ited to non-authorized personnel and the operator
has to wear suitable shoes.
- Signal the areas of moist floors with suitable signs.
- If the machine does not work properly, check by
conducting simple maintenance procedures. Other-
wise, as for technical advice from an authorized as-
sistance centre.
- Where parts are required, ask for ORIGINAL spare
parts from the distributor and/or from an authorized
dealer.
- Use only ORIGINAL brushes indicated in the para-
graph "RECOMMENDED BRUSHES".
- For any cleaning and/or maintenance operation
take off the power supply from the machine.
- Do not take off the protections which require the
use of tools for their removal.
- Do not wash the machine with direct water jets or
with high water pressure nor with corrosive material.
- Every 200 working hours have a machine check by
an authorized service department.
- Before using the machine, check that all panels
and coverings are in their position as indicated in
this use and maintenance catalogue.
- Restore all electrical connections after any mainte-
nance operation.
- Provide for the scrapping of the material of normal
wear (brushes, squeegee blades etc.) following strict-
ly the respective rules.
- When your machine has to stop activity, provide
for the appropriate waste disposal of its materials,
especially oils and electronic components, and con-
sidering that the machine itself has been, where pos-
sible, constructed using recyclable materials.

SYMBOLOGY

Symbol denoting the solution
valve.
Indicates the switch and the
signal lamp of the solenoid valve.
Symbol denoting the brush.
Indicates the switch and the
signal lamp of the brush motor.
Symbol denoting the suction
motor.
Indicates the switch and the
signal lamp of the suction motor.
Symbol that indicates the
position of the outlet plug of
the solution tank.
This symbol indicates that tanks
are to be emptied before rotating
the machine.
Indication of the maximum
temperature of the solution
detergent.
Symbol that indicates the flow
adjuster of the detergent
solution.
16
Symbol denoting the crossed
bin. Indicates that at the end of
its activity, the machine has to
be disposed conforming to the
laws in force.
Symbol denoting the open
book.
Indicates that the operator has
to read the manual before the
use of the machine.
Warning symbol.
Read carefully the sections
marked with this symbol, for
the security of both the
operator and the machine.
Symbol denoting the correct mode to transfer the
machine on uneven surfaces.
GB