En: Installation Instructions; Technical Data - Interlogix DC138 Instrucciones De Instalación

Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

EN: Installation Instructions

Legend for Figures
1
Magnetic contact
2
Installation and connection diagram
A
Contact
B
Magnet
3
Distance diagram
A
Proximity/switch-on distance
B
Distance/switch-off clearance
C
Tolerance zone
D
Contact
E
Magnet
4
Connection
A, B, C,
Connection cable
D
Note: B and D are the 2 twisted cables for the tamper loop.
E
Switching part (NC)
F
Tamper protection (internal reed)
G
EOL resistor
Description
The magnetic contact and the magnet must be mounted facing
each other in a window frame/door leaf and window
surround/door surround.
Caution:
The EN grade 3 flush-mounted magnetic contact
DC138 was specially developed for installation in
ferromagnetic materials.
When installing the snap-on metal flange mounting EF 8/20, a
material strength of 0.5 - 2.3 mm is permissible.
When mounting is complete, the magnetic contact's electrical
switching function must be checked (e.g. using a continuity
tester or multimeter).
The application of mechanical force, e.g., when mounting the
device on the casing may damage the glass body of the reed
switch.
Installation
Snap-on metal installation flange EF 8/20 on the contact and
magnet housing (see Figure 2).
Caution:
Measure the supply lines electrically before
connecting them!
Distance Diagram
See Figure 3.
Minimum switch-on distance:
tolerance in z:
Table 2
Proximity/switch-on distance
Distance/switch-off clearance
2 of 9
9 mm,
max. +/- 3 mm
Switch-on
Tolerance
distance [mm]
[mm]
12
+/- 3
13
+/- 2

Technical Data

Flush-mounted magnetic contact DC138 for EOL zone types,
tamper protected.
Note:
For front flush-mounted installation in ferromagnetic
materials.
Contact type
1 - pin NC contact
Switching distance
12 mm, +/- 3 mm
Switching voltage
max. 100 V DC
Switching current
max. 500 mA
Contact rating
max. 6 W or 6 VA
Contact resistance
max. 0.15 Ohm
Breakdown voltage
> 250 V
Permissible operating
max. 40 V
voltage
Connection cable
LIYY 4 x 0.14 mm Cu tin-plated;
Suitable for LSA IDC method of termination
External cable color
White
Internal conductor
Blue (yellow pattern)
Contact dimensions
Ø 8 x 32 mm with installation flange EF 8/20
(for 20 mm drilled diameter)
Cable dimensions
Ø 3.2 mm x 2 m (DC138)
Ø 3.2 mm x 6 m (DC138S60)
Magnet
Ø 6 x 19 mm neodymium, axially polarized,
in Ø 8 x 25 mm plastic sleeve with installation
flange EF 8/20 ( 20 mm drilled diameter)
Housing material
S-B or A-B-S, flange PA6 GF 30
Color
White
Temperature range
- 25 °C to + 70 °C
Protection category
VdS - environmental class III, IP 67
Scope of Delivery
1 magnetic contact
Ø
1 magnet
6 x 19 mm neodymium in plastic sleeve
Ø
8 x 25 mm with 1 flange EF 8/20
Ø
European Directive
Tested & Certified
EN
EN 50131-2-6 Grade 3 by VdS
VdS no.
G110010 (Cl. C)
European
UTC Fire & Security B.V., Kelvinstraat 7, 6003
Representative of
DH Weert, The Netherlands.
Supplier
The goal of the EC directive on waste electrical
and electronic equipment is to minimize the
environmental and health impact of such
equipment. In accordance with this directive,
electrical devices bearing this symbol must not be
disposed of in the European public waste
disposal systems. European users of electrical
devices must now return all waste electrical and
electronic equipment for recycling. For more
information, please visit: www.recyclethis.info
Contact
See www.interlogix.com.
8 x 32 mm with 1 flange EF 8/20
P/N 31495600.Y71 • REV 2.0 • ISS 14NOV11

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Dc138s60

Tabla de contenido