Cequent Performance Products 24756 Instrucciones De Instalación

Chevrolet HHR including SS*, Chevrolet Cobalt SS sedan & coupe& SS
Supercharged, Cobalt Sport sedan & coupe, Saturn Ion Redline & Ion 3
w/2.4L Engine, Pontiac Pursuit GT sedan & coupe & Pontiac G5 GT.
Vehicle frame
Hitch Shown In Proper Position
Equipment Required:
Fastener Kit: 24756F or 60815F
Wrenches: 3/4"
Drill Bits: 1/2"
*Only on HHR-SS trim plastic
bumper fascia as shown in rear
view of vehicle below
HHR
Trim plastic in middle of
fascia 3" wide up to first bend
j
1/2"-13 X 1-1/2" Carriage Bolt
Qty.(4)
k
1/4" X 1" X 3" Block
Qty.(4)
1. Drop muffler and tailpipe by removing all rubber isolators, behind rear axle, off of hangers. There will be (2) or (3)
depending on vehicle. On Ion Redline rearward isolator hanger needs to be bent down slightly for fastener clearance.
2. Install rearward fasteners. On Cobalt, Pursuit, G5 GT and Ion vehicles it will be necessary to drill both rear holes. Use
rearmost slot that does not go all the way thru frame as guide to drill clearance hole for 1/2" bolts. On HHR it is
necessary to enlarge rearmost slot on passenger side only. Fishwire 1/2" carriage bolts and blocks thru access slots in
bottom of frame both sides.
3. Install forward fasteners both sides. Insert carriage bolts and blocks into access slot and drop back down thru slot
making sure block spans both sides of slot.
4. While holding muffler down slide hitch up and over muffler and into place making sure that you do not push fasteners
back up into frame. Install conical washers and hex nuts on all (4) bolts and do not tighten.
Before tightening bolts slide hitch over towards the passenger's side and up against trunk pan. While holding hitch
5.
against trunk pan tighten bolts.
Tighten all 1/2" fasteners with torque wrench to 75 Lb.-Ft.
6.
7. Reinstall muffler isolator hangers.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body
panels to prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety
precautions when working beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C.
Regulation V-5 and SAE J684.
z
2008, 2015 Cequent Performance Products– Printed in Mexico
Installation Instructions
Drawbar Kit:
Bumper
3594 or 6805
fascia
(Sold separately)
Drawbar must be used in
the RISE position only.
Vehicle frame
This is the location of the slot for
the Cobalt, Ion, Pursuit & G5 GT,
typical both sides. See note below.
Vehicle trunk pan
SS
Enlarge existing rearward slot Cobalt, Ion,
Pursuit & G5 GT only
Tighten all ½" fasteners with torque wrench to 75 Lb.-Ft.
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or
2000 LB Max Gross Trailer Weight
Wiring Access Location:
HHR--------------------------SUV 3 & 4
COBALT 2 Drs. PC3&PC4 --4 Drs. PC1&PC2
ION---------------------------PC3 & PC4
PURSUIT & G5 GT-------PC1 & PC2
l
1/2" Conical washer
Qty.(4)
m
1/2" Hex nut
Qty.(4)
Sheet 1 of 3 24756N
Part Numbers:
24756
77132
60815
200 LB Max Tongue Weight
This is the location of the slot for the
HHR, typical both sides. See note below.
VEHICLE
FORWARD
Enlarge existing
rearward hole/slot
all models.
NOTE!
Hitch has (3) attachment holes/slots per
side but only (2) are used depending on
vehicle. HHR uses center hitch slot and
Cobalt, Ion, Pursuit & G5 GT uses
forward hitch slot. All models use
rearward hole.
10-13-15 Rev. E