Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Frame
Hitch Shown In Proper Position
Equipment Required:
Fastener Kit: 24759N
Wrenches: 3/4", 15mm, 17mm
Drill Bits: 1/2"
Screwdriver
Taillight
access
2
1
Typical both sides
j
1/2"-13 X 1-3/4" Carriage bolt
Qty. (2)
k
1/4" X 1-1/2" X 2" Block
Qty. (2)
l
1/2" Lock washer
Qty. (2)
1.
Remove tow hooks if present. Return tow hooks & fasteners to owner.
2.
Remove both taillights by removing screw at bottom of light cover.
3.
Lower exhaust at (2) hangers, (1) at front and (1) at rear of muffler.
4.
Position hitch as shown and install M10 fasteners provided.
Using hitch as a template, drill 1/2" holes in (2) places.
5.
6.
Fishwire carriage bolt and block through access holes in taillight openings, as shown.
7.
Torque all fasteners to specifications shown below.
8.
Re-install exhaust hangers and taillights.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z
2005, 2015 Cequent Performance Products, Inc. - Printed in Mexico
Installation Instructions
Chrysler PT Cruiser
Bumper
(Sold separately)
Drawbar Kit:
3593
Drawbar must be used in the
RISE position only.
Tighten all 1/2" fasteners with torque wrench to 75 Lb.-Ft.
Tighten all M10 CL8.8 fasteners with torque wrench to 38 Lb.-Ft.
Do Not Exceed Lower of Towing Vehicle
2000 LB Max Gross Trailer Weight
200 LB Max Tongue Weight
Wiring Access Location: SUV 1, SUV 2
Frame rails
Existing weld nuts,
Typical both sides
Drilled holes
both sides
4
3
Typical both sides
m
1/2" Hex nut
Qty. (2)
n
Qty. (4)
M10 X 1.50 X 35mm CL8.8 Hex bolt
o
3/8" Conical washer
Qty. (4)
Sheet 1 of 3
Part Numbers:
Manufacturer's Rating or
Position blocks
as shown
5
6
Typical both sides
24759N
10-13-15
24759
77135
60818
Rev. B
Publicidad
Manuales relacionados para Cequent Performance Products 24759
Resumen de contenidos para Cequent Performance Products 24759
- Página 1 This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. Sheet 1 of 3 24759N 10-13-15 Rev. B 2005, 2015 Cequent Performance Products, Inc. - Printed in Mexico...
- Página 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spé cifications en matiè re de sé curité des systè mes d’attelage. Feuille 2 de 3 24759N 10-13-15 Rev. B 2005, 2015 Cequent Performance Products, Inc. Imprimé au Mexique...
- Página 3 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York. V.E.S.C. Regulació n V-5 y SAE J684 Hoja 3 de 3 24759N 10-13-15 Rev. B 2005, 2015 Cequent Performance Products, Inc. - Impreso en México...