Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Hitch Shown In Proper Position
Equipment Required:
Fastener Kit: 24757F or 60816F
Wrenches: 10mm, 18mm, 9/16
Drill Bits: None
j
Qty. (1)
3/8-16 U-Bolt
k
Qty. (2)
3/8-16 Flanged Locknut
NOTE:
On vehicles with single exhaust, remove appearance panel which covers driver's side frame rail by removing seven fasteners.
Return appearance panel and fasteners to vehicle owner.
1. Lift hitch into position and install u-bolt over vehicle tow hook and down thru holes in vehicle center bracket. Install 3/8" flanged
locknuts.
2. Install M10 bolts and conical toothed washers thru frame straps into existing weld nuts in vehicle frame rails, one per side.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z
2005, 2015 Cequent Performance Products, Inc. - Printed in Mexico
Installation Instructions
Hyundai Sonata
Fascia
(Sold separately)
Drawbar Kit:
3592
Or
6803
Drawbar must be used in the
RISE position only.
Vehicle Frame Rail
Vehicle Tow Hook
Tighten all 3/8 GR2 fasteners with torque wrench to 20 Lb.-Ft.
Tighten all M10 CL8.8 fasteners with torque wrench to 42 Lb.-Ft.
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or
2000 LB Max Gross Trailer Weight
200 LB Max Tongue Weight
Wiring Access Location: PC3, PC4
l
Qty. (2)
M10 x 1.25 x 40mm Hex Bolt
m
Qty. (2)
Conical Toothed Washer
Sheet 1 of 3
24757N
Part Numbers:
24757
77133
60816
10-13-15
Rev. C
Form F206 Rev A 5605
Publicidad
Manuales relacionados para Cequent Performance Products 24757
Resumen de contenidos para Cequent Performance Products 24757
- Página 1 This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. Sheet 1 of 3 24757N 10-13-15 Rev. C 2005, 2015 Cequent Performance Products, Inc. - Printed in Mexico Form F206 Rev A 5605...
- Página 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spé cifications en matiè re de sé curité des systèmes d’attelage. Feuille 2 de 3 24757N 10-13-15 Rev. C 2005, 2015 Cequent Performance Products, Inc. Imprimé au Mexique Form F206 Rev A 5605...
- Página 3 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York. V.E.S.C. Regulació n V-5 y SAE J684 2005, 2015 Cequent Performance Products, Inc. - Impreso en México Hoja 3 de 3...