Publicidad
TECHNICAL SPECIFICATIONS OF THE MOTOR
TYPE OF MOTOR
M63 A2
MOTOR POWER
0.22 kW
POWER SUPPLY
SINGLE PHASE + NEUTRAL + EARTH
INSULATION CLASS
F
MOTOR VOLTAGE
230 VOLT
SERVICE
S1 (WITH NATURAL VENTILATION)
FREQUENCY
50 Hz
ABSORPTION IN AMPERES
1.9 A
RPM
2800 RPM (RATED)
NUMBER OF POLES
2
MACHINE DIMENSIONS
20 x 18 x 26 cm
WEIGHT
10 kg
The sharpening machine is manufactured in accordance with the
following directives:
- Low Voltage Directive 2006/95/EC
- EMC Directive 2004/108/EC
istruzioni fast blade.indd 5
- Machinery Directive 2006/42/EC
considering the following harmonised standards:
EN 60 034-1 / EN 60 034-5 / EN 60 034-09 / EN 60 204-1 / EN 349 /
EN 13857
The machine does not require additional lighting as the lighting in
the environments in which it is used, subject to the applicable safety
standards, is sufficient.
The manufacturer reserves the right to make changes deemed
appropriate as a result of technical developments at any time and
without notice.
PERSONAL PROTECTIVE EQUIPMENT
The signs described below feature on the machine. Read them carefully
and memorise their meaning. The danger symbols must always be
clean and in good condition. Replace them with other original symbols
requested from the manufacturer if necessary. The new symbols must
be affixed in the same positions as the ones being replaced.
1
2
3
4
1) Before starting work, read the operating and maintenance
manual carefully.
2) Before performing maintenance, disconnect the electrical power
supply and consult the operating and maintenance manual.
3) Gloves must be worn.
4) Watch your upper limbs.
5) Goggles must be worn.
INSTALLATION AND PUTTING INTO SERVICE
Remove FAST BLADE© from its packaging and make sure it has
not been damaged during transport. Check that the line voltage
and frequency are as required. FAST BLADE© must be connected
to an electrical system that complies with current legislation and is
properly earthed. Connect the 2p+e plug to the electrical system
outlet.
OPERATING INSTRUCTIONS
INITIAL START-UP:
The first time you use FAST BLADE©, check that it is installed correctly
and that the voltage in the electrical system is 220 V AC.
SWITCHING ON
To start FAST BLADE©, plug it in and set the power switch to " I". If
there is no power, FAST BLADE© will switch off. To reset it, press " O"
and then "I" again.
SWITCHING OFF
To switch off FAST BLADE©, set the power switch to " O".
INSTRUCTIONS FOR SHARPENING
Do not use any liquid or other material on the belts. FAST BLADE©
must only work while dry. Pay particular attention to the types of
blades that can be sharpened.
SHARPENING KNIVES
While sharpening the knife, the operator must stand up straight and
not bend over. To perform successful sharpening:
1. Grip the handle of the knife to be sharpened firmly and position
the blade parallel to the horizontal plane with the tip pointing
forward;
2. Bring the blade into contact along the insertion line created by
the desired angle. 5 different angles can be used, depending on the
result to be obtained:
position no. 1
30 degrees
position no. 2
38 degrees
position no. 3
45 degrees
position no. 4
50 degrees
position no. 5
55 degrees.
5
3. Slide the blade backwards and forwards a few times, applying
very light pressure;
4. Remove the knife by pulling it upwards;
5. Check the result by cutting a piece of paper held vertically;
6. Repeat until achieving the desired level of sharpening (usually
2/3 times).
MAINTENANCE
BELTS
The three abrasive belts positioned inside FAST BLADE© can sharpen
about seventy blades. When the belts become worn, change them to
ensure that sharpening is always efficient.
SAFETY DEVICES AND MALFUNCTIONING
The safety device on the motor is composed of a fuse (black, marked
"FUSE"), positioned by the start button. If the fuse stops working,
the sharpening machine will not operate. In this case, replace the
protective fuse with a new one of the same type and model.
To replace the damaged fuse, unscrew the fuse holder marked " fuse"
in an anti-clockwise directions, remove it and replace it with a new
one. Replace the whole part and screw it in clockwise. Also check that
the protective covers are intact.
PERIODIC EXTERNAL CLEANING
Once a week, clean the extractor, the FAST BLADE© surface and
anywhere metal dust accumulates using a dry cloth, a vacuum
25/09/2012 15:56:52
Publicidad
