Specific Safety Rules; Safety Guidelines - Definitions - Black+Decker HG2000 Manual De Instrucciones

16 • ENGLISH
c. Disconnect the plug from the power source and/or
the battery pack from the power tool before
making any adjustments, changing accessories,
or storing power tools. Such preventive safety measures
reduce the risk of starting the power tool accidentally.
d. Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power
tool. Power tools are dangerous in the hands
of untrained users.
e. Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts and
any other condition that may affect the power
tools operation. If damaged, have the power tool
repaired before use. Many accidents are caused by
poorly maintained power tools.
f. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
5. Service
a. Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
6. Electrical safety
Your tool is double insulated; therefore no earth
wire is required. Always check that the main
voltage corresponds to the voltage on the rating
plate.
Warning! If the power cord is damaged, it must
be replaced by the manufacturer, authorized
BLACK+DECKER Service Center or an equally
qualified person in order to avoid damage or
injury. If the power cord is replaced by an equally
qualified person, but not authorized by
BLACK+DECKER, the warranty will not be valid.
7. Labels on tool
The label on your tool may include the following symbols:
Hz .......
Read
Instructions
W ........
Manual
min .....
Use Eye
Protection
Use Ear
Protection
V ........ Volts
n .......
0
A ........ Amperes
Hertz
...... Class II
Watts
....
minutes
..... Alternating
....
Current
..... Direct
.../min..
Current
No-Load
Speed
SAFETY GUIDELINES/DEFINITIONS
It is important for you to read and understand this manual.
The information it contains relates to protecting your
safety and preventing problems. The symbols below are
used to help you recognize this information.
Danger! Indicates an imminently hazardous situation
which, if not avoided, will result in death or serious injury.
Warning! Indicates a potentially hazardous situation
which, if not avoided, could result in death or serious
injury.
Caution! Indicates a potentially hazardous situation
which, if not avoided, may result in minor or moderate
injury.
Caution! Used without the safety alert symbol indicates
a potentially hazardous situation which, if not avoided,
may result in property damage.
ADDITIONAL SAFETY INSTRUCTIONS
Warning! This tool should be placed in its holder
when not in use.
f Remember that hidden areas such as those behind
walls, ceilings, floors, soffit boards and other
panels may contain flammable materials that could be
accidentally ignited when stripping paint from the panel.
Such a fire would not be readily apparent, and
could cause considerable damage and danger
of injury. These heat guns are capable of producing
temperatures in excess of 1000°F (538°C).
f Do not use this tool as a hair dryer.
f Allow the tool to cool before storing. Do not lay the
heat gun on flammable surfaces when operating the
gun or immediately after shutting it off. Always set
the gun on a flat level surface so that the nozzle tip is
pointed upward.
f Always use good quality scrapers and stripping
Construction
knives.
Earthing
f Never obstruct the air intake or nozzle outlet.
Terminal
f Be sure to direct the hot air blast in a safe direction;
Safety Alert
Symbol
away from other people or flammable objects.
Revolutions
f Keep fingers away from metal nozzle; it becomes very
or Recipro-
hot.
cation per
minute
f Don´t touch the nozzle to any surface while running or
shortly after running.
f Avoid poking anything down inside the nozzle.
f Know your work environment. Remember that areas
behind soffit board, ceilings, and floors may contain

SPECIFIC SAFETY RULES

FOR HEAT GUNS