Krups XP4050 Instrucciones De Uso página 7

handle and use the flat end of the measur-
ing spoon to Polish the top of the coffee
but do not tamp or compress the ground
coffee into the filter.
Remove any ground coffee from around
•
the top rim of the filter handle to create a
good seal to the brewing head.
Replace the filter holder into the machine.
•
Turn the filter holder until it is firmly locked
into place (6) (7).
Place one or two espresso cups beneath
•
the filter holder.
As soon as the coffee selection buttons
begin to glow continuously, the machine is
ready to operate
Your machine is already preprogrammed
for the preparation of one or two cups of
espresso.
• Press your choice of coffee size by pres-
sing the respective coffee selection button
or (9) (10). Take the pre-brewing
into account.
• When the programmed quantity is rea-
ched, espresso stops running automaticly.
• Remove the filter holder and the filter
from the machine and take out the coffee
grounds (13).
• Put the filter holder with the empty filter
in place (6) (7) and push the brew button
to purge and clean the filter of coffee
sediment.
The filter basket can be refilled to make
more espressos.
Caution: if the water container is empty
and the pump is running, you will hear
a very distinct noise, which is louder
than the normal operating sound. If this
happens, press the start/stop switch (4).
Check the water container and refill as
needed.
Never let the machine run when the water
container is empty as this can damage
the pump.
U
sing the special
"E.S.E.", which stands for "Easy Serving
Espresso", is a selected measure of coffee,
ground and pressed between two filter
papers making a coffee pod which is ready
to use (for example "illy  pods). This sys-
tem makes it easy for you to prepare your
espresso and to clean the machine.
10
" e.s.e. "
filter
The E.S.E. system was designed for making
Italian-style "espresso ristretto" or "short
espresso".
We do not intend, or recommend, that
the E.S.E. servings be used for making
more then one single serving or a "long
espresso".
We recommend that you take care when
handling and storing the E.S.E. pre-por-
tioned pods so that they do not become
deformed.
For best results, we recommend that you
pre-heat the accessories (filter holder, filter
basket and cups) without any coffee. To do
this, see section entitled "Espresso Making"
above.
. Preparing an espresso:
• Fill the water tank (1) (2) (3) and turn on
the machine (4).
Setting the E.S.E. pod (18).
Tear excess paper from pod at perforated
edge. Place the E.S.E. pod with the RED
MARKING FACE DOWN (bend the paper
corners down) in the E.S.E. filter holder
fitted with its own filter.
• Take care to put all the paper inside the
filter or you may have some drips.
Placing the E.S.E. pod correctly will create a
richer, thicker crema.
Locking the handle tightly and properly will
also help avoid leakage from the filter holder
and ensure a better brewing cycle.
Place the filter holder inside the brewing
head and firmly turn the handle as far right
as possible (6) (7) (8).
As soon as the coffee selection buttons
commence to glow continuously, the
machine is ready to operate.
• Press the single serving coffee button
(9). Take the pre-brewing into account.
• When the recommended quantity of coffee
has been reached (35ml), press the coffee
button (9) again if suitable volume was
not preprogrammed.
• Remove the filter holder from the brewing
head and throw away the used coffee pod.
NOTE: All pods (such as those sold by
Starbucks  and Illy ) can be used in your
Krups XP 4050 as long as they are E.S.E.
standard pods.