Safety Regulations - EINHELL TC-SM 2531/1 U Manual De Instrucciones Original

Sierra ingletadora
Ocultar thumbs Ver también para TC-SM 2531/1 U:
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

Danger!
When using the equipment, a few safety pre-
cautions must be observed to avoid injuries and
damage. Please read the complete operating
instructions and safety regulations with due care.
Keep this manual in a safe place, so that the in-
formation is available at all times. If you give the
equipment to any other person, hand over these
operating instructions and safety regulations as
well. We cannot accept any liability for damage
or accidents which arise due to a failure to follow
these instructions and the safety instructions.

1. Safety regulations

Danger!
Read all safety regulations and instructions.
Any errors made in following the safety regula-
tions and instructions may result in an electric
shock, fi re and/or serious injury.
Keep all safety regulations and instructions
in a safe place for future use.
Special information about the laser
Caution! Laser radiation
Do not look directly into the beam
Laser class 2
Precaución Radiación Laser
No mirar al haz de laser
Especificación Laser
Segun EN 60825-1
Laser clase: 2
: 650 nm; P
Never look directly into the laser path.
Never direct the laser beam at reflecting sur-
faces or persons or animals. Even a low out-
put laser beam can inflict injury on the eye.
Caution: It is vital to follow the work proce-
dures described in these instructions. Using
the equipment in any other way may result in
hazardous exposure to laser radiation.
Never open the laser module.
When the crosscut saw is not going to be
used for an extended period of time, the bat-
teries should be removed.
It is prohibited to carry out any modifications
to the laser to increase its power.
The manufacturer cannot accept any liability
for damage due to non-observance of the
Anl_TC_SM_2531_1_U_SPK8.indb 23
Anl_TC_SM_2531_1_U_SPK8.indb 23
GB
0
- 23 -
safety information.
Safety instructions
Danger! When using electric tools, basic sa-
fety precautions should always be followed
to reduce the risk of fi re, electric shock
and personal injury, including the following.
Read and follow these instructions before
using the equipment and keep the safety in-
formation in a safe place.
1. Keep work area clean
– Cluttered areas and benches invite injuries.
2. Consider work area environment
– Don't expose power tools to rain. Don't use
power tools in damp or wet locations. Keep
work area well lit. Don't use power tools in
presence of fl ammable liquids or gases.
3. Guard against electric shock
– Prevent body contact with grounded sur-
faces (e.g. pipes, radiators, ranges refrigerati-
ors).
4. Keep children away
– Do not let visitors contact tool or extension
cord. All visitors should be kept away from
work area.
5. Store idle tools
– When not is use, tools should be stored in
dry, high, or locked-up place, out of the reach
of children.
6. Don't force tool
– It will do the job better and safer at the rate
for which it was intended.
7. Use right tool
– Don't force small tools or attachments to do
the job of heavy duty tool. Don't use tools for
purposes not intended: for example, don't use
circular saw for cutt- ing tree limbs or logs.
8. Dress properly
– Do not wear loose clothing or jewelry. They
can be caught in moving parts. Rubber gloves
and nonskid footwear are recommended
when working outdoors. Wear protective nair
covering to contain long hair.
9. Use safety glasses
– Also use face or dust mask if cutting opera-
tion is dusty.
10. Don't abuse cord
– Never carry tool by cord or yank it to discon-
nect it from receptacle. Keep cord from heat,
oil and sharp edges.
11. Secure work
– Use clamps or a vise to hold work. It's safer
than using your hand and it frees both hands
to operate tool.
06.03.2018 14:02:36
06.03.2018 14:02:36

Publicidad

Capítulos

Tabla de contenido
loading

Tabla de contenido