Technical Data; Before Starting The Equipment; General Information - EINHELL TC-SM 2531/1 U Manual De Instrucciones Original

Sierra ingletadora
Ocultar thumbs Ver también para TC-SM 2531/1 U:
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

saw zone.
Reaching into the running saw blade (cut inju-
ries).
Kick-back of workpieces and parts of workpi-
eces.
Saw blade fracturing.
Catapulting of faulty carbide tips from the saw
blade.
Damage to hearing if ear-muffs are not used
as necessary.
Harmful emissions of wood dust when used
in closed rooms.

4. Technical data

See warranty card of your country.
Wear ear-muff s.
The impact of noise can cause damage to hea-
ring.
Total vibration values (vector sum of three direc-
tions) determined in accordance with EN 61029.
Vibration emission value a
K uncertainty = 1.5 m/s
The specifi ed vibration value was established in
accordance with a standardized testing method. It
may change according to how the electric equip-
ment is used and may exceed the specifi ed value
in exceptional circumstances.
The specifi ed vibration value can be used to
compare the equipment with other electric power
tools.
The specifi ed vibration value can be used for initi-
al assessment of a harmful eff ect.
Keep the noise emissions and vibrations to a
minimum.
Only use appliances which are in perfect wor-
king order.
Service and clean the appliance regularly.
Adapt your working style to suit the appliance.
Do not overload the appliance.
Have the appliance serviced whenever ne-
cessary.
Switch the appliance off when it is not in use.
Caution!
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
Anl_TC_SM_2531_1_U_SPK8.indb 28
Anl_TC_SM_2531_1_U_SPK8.indb 28
< 2.5 m/s
2
h
2
- 28 -
GB
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment's construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.
3. Health damage caused by hand-arm vib-
rations if the equipment is used over a pro-
longed period or is not properly guided and
maintained.

5. Before starting the equipment

Before you connect the equipment to the mains
supply make sure that the data on the rating plate
are identical to the mains data.
Warning!
Always pull the power plug before making
adjustments to the equipment.

5.1 General information

The equipment must be set up where it can
stand securely, i.e. it should be bolted to a
workbench, a universal base frame or similar.
All covers and safety devices have to be pro-
perly fitted before the equipment is switched
on.
It must be possible for the blade to run freely.
When working with wood that has been pro-
cessed before, watch out for foreign bodies
such as nails or screws, etc.
Before you actuate the On/Off switch, make
sure that the saw blade is correctly fitted
and that the equipment's moving parts run
smoothly.
5.2 Assembling the base frame
(Fig. 1, 4a – 4e)
Assemble the base frame as shown in Fig.
4a-4e. Attach the parts together using the
screws (a), spring washers (b), washers (c)
and nuts (d). Do not fully tighten the screws
yet.
Start with the top cross struts (101) and the
top longitudinal struts (102) followed by the
leg upper sections (105).
Next, mount the bottom cross struts (103)
and bottom longitudinal struts (104) along
with the legs (105). Then mount the rubber
feet (106) on the legs.
Turn the complete base frame around and
tighten all of the screws.
06.03.2018 14:02:36
06.03.2018 14:02:36

Publicidad

Capítulos

Tabla de contenido
loading

Tabla de contenido